Whirlpool Wtw5100vq0 Parts

Contains two, six foot long braided hoses with 90 degree ends.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

This rotary, 3-position temperature selector switch lets you choose the cycle's temperature. When it wears out, settings may not respond or temperatures may be wrong. Replacing it restores accurate temperature selection and dependable performance.

• Provides user control of temperature with three selectable positions
• Sends the chosen setting to the appliance's control system to achieve the requested temperature
• Common signs of failure: only one setting works, temperature doesn't match the selection, or the selector is loose/hard to turn
• Visible damage to the switch shaft or terminals

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/console
• Note wire locations and transfer them one-by-one (or take a photo for reference)
• Reinstall the existing knob, aligning the flat on the shaft as removed

Includes drive tube spacer, "T" bearing and both shaft seals.

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

Used from harness to top.

Used for the pressure switch.

Right hand side

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

Size: .20 Fl. Oz. (6 ml)

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.