Whirlpool Wtw5800bw0 Parts

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

This impeller cap fits over the dishwasher's wash pump impeller to secure it in place and help maintain proper water flow and spray pressure for effective cleaning. Replacing a cracked or missing cap can reduce noise and restore consistent performance.

• Secures the wash pump impeller and helps prevent wobble or rubbing
• Helps maintain proper water circulation to the spray arms
• Common symptoms of a failed/missing cap: poor cleaning, unusual grinding/rattling noises, or visible damage in the pump area
• Designed for the specific pump/sump design used on select models

• Disconnect power and turn off water supply before servicing
• Access the pump from inside the tub; remove the lower rack, spray arm, and filter/cover as required
• Note cap orientation; press or twist-lock fully onto the impeller (reuse any existing fastener if your model uses one)
• Inspect the impeller and seals while accessible; replace worn parts as needed

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This replacement housing restores the appliance's outer enclosure to protect internal components and maintain proper airflow and fit. It provides a clean, secure mounting surface and helps reduce noise and debris entry. What it does:

• Replaces a cracked, dented, or missing outer housing to restore appliance appearance and protection
• Helps maintain correct airflow paths for heating and ventilation components
• Provides secure mounting points for internal assemblies and fasteners
• Can reduce rattling or vibration caused by a loose or damaged panel
• Prevents dust and debris from entering sensitive internal parts

• One outer housing panel

• Disconnect power (and gas if applicable) before starting any repair
• Handle edges carefully; panels can be sharp—wear gloves and eye protection
• Basic hand tools required; follow OEM service manual for disassembly/reassembly steps

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

This tub ring is the replacement sealing ring that fits around the washer's outer tub to help keep the wash basket secured and reduce vibration. It restores proper sealing and alignment for reliable washer operation. What it does:

• Provides a protective seal between the inner basket assembly and the outer tub
• Helps reduce noise and vibration caused by a loose or worn tub interface
• Prevents minor rubbing or chafing between rotating parts
• Can help address symptoms like unusual noise, rubbing sounds, or movement in the wash basket

• One tub ring

• Disconnect power and water supply before starting any repair
• Basic disassembly of the cabinet or tub may be required; follow the machine's service manual
• Use proper tools and take care not to damage the tub finish or nearby components

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

5 foot. Package of 2.