Whsdr315daww Parts

This leveling leg threads into the base of your washer to set height and keep the cabinet stable on uneven floors. Replacing worn or missing legs reduces vibration, walking, and noise for smoother, safer operation.

• Provides an adjustable foot to level and support the washer
• Helps reduce vibration, rocking, and "walking" during spin
• Replaces stripped, cracked, or missing leveling feet
• Helps with excessive shaking, rattling noises, or out-of-balance conditions

• Disconnect power and water; pull the washer forward for access.
• Support the appliance to prevent tipping; unscrew the old leg by hand or with pliers.
• Thread the new leg into the base; adjust all feet until level front-to-back and side-to-side.
• Ensure each foot contacts the floor firmly and the cabinet is stable before use.

This tub assembly replaces a cracked or leaking wash tub to restore proper water containment and drum support for your washer, helping reduce leaks, rubbing noises, and abnormal vibration during cycles. What it does:

• Provides the sealed reservoir that holds wash water and supports the inner drum during wash and spin cycles
• Helps stop or reduce water leaks caused by cracked or damaged tubs
• Can resolve rubbing, scraping, or thumping noises from a warped or broken tub
• Helps stabilize the drum to reduce vibration and improve spin performance

• Disconnect power and shut off water supply before starting; wear gloves and eye protection
• Tub assemblies are heavy and bulky—use two people or appropriate lifting equipment
• Follow the washer OEM service manual for disassembly, seal transfer/replacement, and torque specifications
• If bearings, seals, or mounting hardware show wear, replace them per OEM guidance for a complete repair

Transmission drive pulley nut.

Includes 12 washers.

This power line filter sits between household AC and the washer's internal wiring to reduce electrical interference and help stabilize control operation. Replacing a failed filter may restore power and prevent nuisance breaker or GFCI trips.

• Filters incoming AC power to reduce electromagnetic interference reaching the control and motor circuits
• Helps prevent interference-related issues like erratic controls or random resets
• Failure may present as no power/blank display, intermittent power loss, or tripping a breaker/GFCI
• Visual clues of failure can include scorching, swelling, or a cracked housing

• Unplug the washer or switch off the circuit breaker before servicing; allow a few minutes for internal components to discharge
• Access the filter location (often near the control area or rear panel) per your model's service information
• Note wire locations (LINE, LOAD, and GROUND) and move one lead at a time to avoid miswiring
• Mount securely and ensure the ground connection to the cabinet is tight for proper operation

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Secure your washer's drain hose with this drain hose strap. It keeps the hose positioned at the standpipe or laundry tub, helping prevent movement, dislodging, and messy leaks when vibration increases during drain and spin cycles.

• Secures the drain hose to a standpipe or utility sink, per installation guidelines
• Helps prevent the hose from backing out or spraying water during operation
• Reduces strain and kinking by keeping the hose routed in place
• Replaces a missing, cracked, or broken strap

• Unplug the washer and turn off water supply before starting
• Position the drain hose in the standpipe or tub and tighten the strap to secure it without kinking the hose
• Maintain the manufacturer-recommended air gap and hose height per your installation manual
• Run a quick drain/spin to ensure the hose stays secured and there are no leaks

Size: 14-10 a trt 7/8 s.

This lid switch assembly detects when the washer lid is closed and lets the machine start and complete cycles. Replacing a failed switch restores the washer's safety interlock and helps resolve start/spin problems. What it does:

• Detects lid closure to enable motor and spin cycles
• Prevents the washer from starting or spinning when the lid is open
• Common replacement for washers that won't start, won't spin, or stop mid-cycle
• Completes the electrical safety/interlock circuit for proper operation

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access may require removing the top or rear access panel; keep track of fasteners and wire locations
• Disconnect wiring harness and replace the switch assembly; ensure secure mounting and correct connector seating

This 2-speed clutchless motor replaces the washer's drive motor to restore agitation and spin without a mechanical clutch. It provides the two common drive speeds used for agitate and spin cycles on compatible top-load washers. What it does:

• Turns the washer tub/agitation mechanism to enable agitate and spin functions
• Operates at two speeds (agitate and spin) using an internal clutchless design
• Commonly used when a washer hums, runs but won't agitate or spin, or fails to change between agitate and spin
• Works with the existing mounting bracket and wiring harness on compatible models

• Disconnect power before servicing to avoid shock or injury
• Motor is heavy and may require lifting assistance; support the tub during removal/installation
• Reuse the existing mounting hardware and wiring harness
• Follow the washer's service manual for disassembly, torque, and wiring routing; test operation before reassembling the cabinet

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

Size: 8-32 t. Includes 12 screws.

Size: 8-18 ab.

This hex nut overmold assembly secures appliance components while the molded sleeve protects surrounding surfaces and reduces vibration. It replaces worn or missing fasteners to restore a secure fit and help prevent rattling or movement. What it does:

• Provides a threaded fastening point for panels, trim, or internal brackets
• Molded overmold sleeve protects finishes and helps isolate vibration
• Restores secure mounting when a nut is stripped, missing, or loose
• Helps reduce rattling and movement of attached parts

• Disconnect power and follow appliance-specific safety procedures before starting
• Tighten by hand then snug with the appropriate wrench; avoid overtightening to prevent damaging the molded sleeve

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts