Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces worn oven door seals that allow heat to escape or show visible damage. Creates a tight barrier to maintain temperature and efficiency. Confirm fit.
Turned the power off. Lifted the oven door up and off.to make access easier and to clean an replace gasket.Then unscrewed the element brackets. Cleaned oven. Took oven door apart to replace gasket ,you have to separate the door halves to clean window and get the gasket out. This is where you better take pictures and notes. You need a large work bench and a good #2 Phillips. Taking the elements out you will deal with gouged out screws, rust stripped threads etc. You may need to buy some self... Read more
Replace a cracked or broken washer door hinge that no longer supports the door properly. Installs on the door frame to provide smooth opening.
Range indicator light assembly illuminates control panel displays. Replace when light fails or flickers. Verify fit with your model number.
Replace your broken or missing range clock knob. Mounts to the control panel for adjusting the built-in clock. Order a new knob if yours is cracked or worn.
Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.
Replaced leg mount and leg. Read more
Wrench designed to adjust leveling legs on washers and dryers. Install to properly level your appliance and reduce rocking. Needed when original is missing.
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Shoulder screw that secures oven components with a precise pivot or spacer point. Replace if missing, worn, or stripped to restore alignment and stability.
I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more
Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.
Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.
Leveling leg for washers. Installs at the base to support and level your machine. Replace if cracked, broken, worn, or missing for proper stability.
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
Replaced burners and cleaned Read more
10-32 x 3/8 machine screw that secures cooktop panels, brackets, and trim. Replace if stripped, rusted, or missing to keep components properly aligned.
Fix excessive washer vibration and loud spinning with a new balance weight. Stabilizes the tub during spin cycles. Moderate DIY repair for most models.
Secures hoses and wiring to prevent movement and vibration wear in your dishwasher. Replace if clips are cracked or connections have loosened.