Wm2688hnw Parts

This door boot gasket seals the gap between the washer tub and front opening to keep wash water contained. Replace a torn, cracked, or deformed boot to stop front leaks and restore a reliable door seal.

• Creates a flexible, watertight seal between the outer tub and door opening
• Helps prevent water leakage from the front of the washer during cycles
• Common failure signs: visible tears or cracks, water on the floor near the door, door not sealing properly
• Wear, sharp objects, or overloading can damage the gasket over time

• Disconnect power and turn off water before servicing; wear gloves to protect hands from sharp cabinet edges
• Remove the outer spring clamp and peel the old boot from the front panel
• Access the inner clamp from inside the cabinet (front/top panel removal may be required); align index marks on the new boot and reconnect any small hoses/vents if present
• Seat the gasket evenly, reinstall both clamps, and run a short test to check for leaks

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

Locking pin for shock absorber.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This pump hose routes washer tub water to the drain pump, helping remove wash water during the drain cycle. Replace a cracked or clogged hose to stop leaks and restore normal draining. What it does:

• Channels tub water to the drain pump so the washer can expel water during drain/spin cycles.
• A worn or cracked hose can cause water leaks under the machine.
• Blocked or collapsed hoses can contribute to slow or incomplete draining.
• Compatible replacement for the OEM pump hose connection on qualifying LG washers.

• One pump hose (single hose as shown)

• Disconnect power and turn off water supply before beginning any repairs.
• Confirm correct routing and secure clamps when installing to prevent leaks.
• Inspect adjacent clamps and fittings for wear; replace if corroded or damaged.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

Includes sensor probe

This lamp assembly restores the interior drum light in your washer, improving visibility when loading and unloading. Replace a failed or damaged light to clearly see items and check the tub at a glance.

• Illuminates the washer drum when the door/light function is active
• Replaces a burned-out, flickering, or physically damaged lamp assembly
• Connects to the existing wiring harness and mounts in the factory location
• Symptoms include: drum light not turning on, intermittent flicker, or a cracked lens/housing

• Unplug the appliance before servicing; turn off water supply if opening the cabinet
• Access varies by model; may require removing the top/front panel and door boot clamp
• Disconnect the wiring connector carefully, seat the new assembly fully, secure it, and verify light operation before reassembly

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.