Wm3479hwa Parts

This bellows is the flexible door boot seal that helps keep water contained in the washer tub and maintains a watertight seal around the front-load door. It replaces a damaged or leaking door boot to reduce leaks and restore proper sealing. What it does:

• Forms a flexible, watertight seal between the washer door and tub to help prevent leaks
• Keeps laundry water inside the drum during wash and rinse cycles
• Helps maintain drum pressure balance and proper door closing
• Commonly replaced when cracked, torn, or permanently deformed

• One bellows

• Recommended for front-load washers; fit with your model before ordering
• Typical replacement requires removing the outer and/or inner door trim and detaching clamp(s)
• Disconnect power and water supply before beginning any repair to avoid injury

This outer tub assembly is the main exterior drum that holds the inner tub and water during a wash cycle, restoring the washer's sealed water chamber and structural support. Replace a damaged outer tub to correct leaks and restore proper operation. What it does:

• Holds and seals water inside the washer's wash chamber for normal fill and drain cycles.
• Provides structural support for the inner tub and suspension system to reduce vibration.
• Replaces a cracked, warped or corroded outer tub that can cause visible leaks.
• Can address symptoms such as persistent leaks, unusual vibration or noise originating from the tub area.

• One outer tub assembly

• Disconnect power and water supply before starting any repair.
• Outer tub replacement may require transferring the inner tub, seals, and other components; inspect and replace seals or gaskets if worn.
• Use proper lifting support—tub assemblies are heavy and awkward to handle; consider a second person.
• Verify appliance compatibility with the part number before ordering.

This replacement connector hose routes water between the refrigerator water valve and the dispenser or ice maker, restoring reliable water flow and helping prevent leaks. It's a direct-fit service part used where the factory hose is worn or damaged. What it does

• Connects the refrigerator water valve to the dispenser or ice maker, providing a sealed water path.
• Restores proper water and ice delivery when a cracked or leaking hose causes reduced flow or pooling.
• Helps prevent leaks by replacing brittle, cracked, or split tubing and fittings.
• Works with the original fittings and routing used by the manufacturer for a secure connection.

• One replacement connector hose.

• Turn off and disconnect the refrigerator's water supply and power before starting.
• Verify orientation and routing match the original hose; avoid sharp bends or kinks.
• Tighten fittings securely but avoid over-tightening; inspect for leaks after reconnecting water.

This filter assembly replaces the water/ice filter housing and valve connections in compatible refrigerators to restore proper water flow to the dispenser and icemaker. It helps stop leaks and resolve low or no-water flow when the housing is faulty. What it does

• Replaces the internal filter housing and inlet/outlet connections that route water to the dispenser and icemaker.
• Restores normal water flow and pressure when a cracked or damaged housing causes leaks or restricted flow.
• Helps prevent leaks that can occur from worn seals or damaged fittings in the filter assembly area.
• Can resolve symptoms such as reduced dispenser flow, intermittent water flow to the icemaker, or visible leaks near the filter area.

• One filter assembly (housing and associated valve/connectors) as shown

• Turn off the refrigerator water supply and unplug the appliance before beginning work.
• Relieve system pressure by dispensing water after shutoff and have towels ready to catch residual water.
• Inspect and tighten all connections; replace any O-rings or seals if specified by OEM instructions.
• After installation, turn the water back on, check for leaks, and flush several liters through the dispenser per manufacturer guidance before use.

This door gasket seals the refrigerator door to keep cold air in and maintain consistent temperatures. Replaces a worn or damaged seal to help reduce energy loss, frost buildup, and moisture inside the compartment. What it does:

• Creates an airtight seal between the door and cabinet to retain cold air.
• Helps prevent warm air infiltration that can cause temperature swings and food spoilage.
• Reduces condensation, frost buildup, and excess cycling of the compressor.
• Restores proper door closing and helps improve overall cooling efficiency.

• High-level swap: remove the old gasket and press or screw the new gasket into the door channel per OEM instructions.
• Inspect mounting channel and hinge alignment before installation; realign door if it does not seat evenly.
• If gasket appears loose after installation, warm gently and refit to improve sealing.
• Disconnect power only if instructed by the OEM for access; otherwise follow basic electrical safety and wear gloves as needed.

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

This rear cover replaces the cabinet back panel that protects internal components and helps maintain proper airflow. Restores enclosure integrity and reduces noise or debris entry when the original cover is cracked, warped, or missing. What it does:

• Shields motors, wiring and controls from dust, lint and accidental contact.
• Directs airflow path and helps avoid airflow-related performance issues.
• Reduces vibration noise caused by loose or damaged back panels.
• Prevents small objects from entering the appliance rear and creating hazards.

• One rear cover (cabinet back) as shown.

• Disconnect power (unplug or shut off breaker) before attempting any repairs.
• Access requires moving the appliance and removing exterior fasteners—keep track of screws and clips.
• Inspect surrounding seals and mounting points; replace any damaged hardware to ensure a secure fit.

This door inner frame is the replacement inner panel frame that supports the door liner and trim, restoring proper fit and appearance. It helps keep the door assembly aligned and finished for normal operation and seal integrity. What it does:

• Provides structural support for the door liner and attached trim pieces
• Restores correct alignment and fit of the door assembly
• Helps maintain a proper door seal and reduces drafts or uneven closing
• Replaces cracked, warped, or cosmetically damaged inner door framing

• One door inner frame

• Disconnect power to the appliance before starting any door repair
• Removal typically requires taking off door trim and inner liner; keep fasteners organized
• Inspect door gasket, hinges, and hardware while replacing the frame; replace any damaged hardware