Wm3997hwa Parts

This washer door boot gasket (bellows) seals the opening between the outer tub and the front panel on front-load machines, keeping wash water inside the drum. Replace when the seal is torn, cracked, or leaking around the door.

• Forms a flexible, watertight seal between the tub and door opening
• Helps prevent leaks during fill, wash, and spin cycles
• Typical failure signs: water on the floor at the front of the washer
• Visible rips, cracks, or warping of the boot
• Drips or seepage from the door area after a cycle

• Unplug the washer and shut off water supply before servicing
• Remove the outer and inner retaining clamps and front panel as required by your model to access the boot
• Note the boot's orientation and alignment marks; match the same orientation on the new gasket
• Ensure the gasket lip is fully seated in the grooves; reinstall clamps evenly and securely

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

This duct outlet directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and a finished connection. It replaces damaged or cracked outlets that can cause leaks, rattles, or restricted airflow. What it does:

• Provides a secure discharge path for exhaust air from the appliance
• Restores a sealed connection to the vent system to reduce leaks and lint escape
• Replaces cracked, warped, or broken outlet pieces that cause rattling or poor airflow
• Helps prevent airflow restriction that can extend drying times or stress the dryer

• Disconnect power and gas before servicing the dryer
• Work in a well-lit area and note existing vent/clamp orientation before removal
• Use gloves to protect hands from sharp sheet-metal edges
• Check and tighten clamps or seals after installation; replace any damaged vent hose or hardware

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

This is the outer tub assembly for the washer — the stationary outer container that holds water and supports the inner wash basket. Replacing a damaged outer tub restores proper water containment and basket support. What it does:

• Holds and contains wash water during cycles to prevent leaks
• Provides the structural support and mounting surface for the inner tub and seals
• Prevents inner tub contact with cabinet and reduces vibration when intact
• Failing tubs can cause visible water leaks, reduced spin performance, or unusual noises

• Disconnect power and water supply before starting any repair
• Replacement may require transfer of inner tub, seals, bearings or mounting hardware from the old tub — only install parts that are explicitly included
• Use proper tools and follow the OEM service manual; tub assemblies can be heavy — get assistance to avoid injury
• Inspect and replace seals, gaskets, and bearings as recommended to ensure a water-tight installation

This outer housing case protects internal components and provides the appliance's external structure for reliable operation and a finished appearance. It helps keep parts aligned and shields electronics and mechanisms from debris and damage. What it does:

• Covers and protects internal components from dust and accidental contact
• Keeps internal modules properly positioned and supported
• Restores the appliance's exterior appearance and structural integrity
• Stops rattles or vibrations caused by a damaged or missing panel

• One outer housing case

• Disconnect power and water before beginning any repair
• Handle panel edges carefully to avoid cuts or cosmetic damage
• Use manufacturer-recommended fasteners; do not overtighten screws

This clamp secures flexible hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal on water and drain lines. What it does:

• Holds a hose firmly to a barb or nipple to prevent slipping and leaks
• Helps stop common symptoms like dripping, visible leaks, or a loose hose connection
• Keeps hoses from shifting or vibrating during operation
• Works wherever a small metal hose clamp is used on plumbing or drainage connections

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide the clamp over the hose, seat the hose on the fitting, then tighten or crimp per the clamp type
• Use pliers or the correct tool for the clamp to avoid damage to the hose or clamp
• Replace with the same clamp style and size for a proper fit; inspect hose and fitting for wear

This replacement balance weight helps stabilize the washer tub during spin cycles to reduce excessive shaking and banging. Restores proper weight distribution so the washer runs more quietly and completes cycles without heavy vibration. What it does:

• Adds counterweight to the washer tub to help balance loads during spin.
• Reduces shaking, banging, and excessive movement during high-speed spins.
• Can help prevent intermittent off-balance conditions and noisy operation.
• Works as a direct replacement for worn, cracked, or missing tub weights.

• Disconnect power and turn off water supply before beginning any repairs.
• Access may require removing the washer cabinet or front panel; follow the model-specific service manual.
• Wear gloves and eye protection; use appropriate tools and fasteners to secure the weight.

A complete replacement door assembly that restores the appliance's barrier, fit and appearance. Replaces a damaged, dented or cracked door so the appliance closes properly and looks like new again. What it does:

• Restores the door panel, edges and mounting points so the door seals and aligns correctly
• Replaces cosmetic damage like dents, scratches or cracked panels
• Helps stop air leaks and temperature loss when the original door is bent or warped
• Provides the mounting surface for handles, hinges and any attached hardware

• Disconnect power to the appliance before starting and work with the appliance empty
• This assembly is large and may require two people to handle and install safely
• Installation typically requires removing hinge fasteners and transferring any handles, trim or gaskets from the old door
• Follow manufacturer instructions and replace any damaged fasteners or seals for a secure fit

This is a hinge assembly for the refrigerator door that restores smooth, aligned door movement and helps the door close properly. Replaces a worn or damaged hinge to stop sagging, rubbing, or uneven gaps. What it does:

• Provides the pivot and mounting points that let the door open and close smoothly
• Corrects door misalignment and eliminates sagging or binding
• Helps seals seat evenly so the door can fully close
• Replaces corroded, bent, or broken hinge hardware that causes noise or uneven operation

• One hinge assembly

• Disconnect power to the appliance before starting and remove any door contents
• Follow OEM instructions for removing the door and supporting it while replacing the hinge
• Use proper hand tools; fasteners may require holding the door in position during reassembly
• If hinge includes grease or bushings, inspect and retain/replace as needed per OEM guidance