Wm4000hba Lg Thinq Parts

The Shipping Bolt is an OEM part for LG washing machines, designed to secure the washing machine's drum during transportation. These bolts are important for preventing damage to the drum and suspension system by immobilizing the drum, thereby avoiding any excessive movement or vibrations that could occur while moving the appliance. 

Causes of a bad shipping bolt can include improper removal during installation, damage from handling, or degradation over time if it was left in place during operation. A damaged or missing shipping bolt can lead to issues with the washing machine's drum alignment and overall stability.

Symptoms that indicate the shipping bolts need removal or installation include:

• Excessive noise or vibrations during operation, suggesting the bolts were not removed after installation.
• Damage to the washing machine's drum or suspension system after moving the appliance without the bolts properly installed.

This OEM LG part can also be used on Kenmore/Sears appliances. 

Restore accurate feedback to your appliance with this sensor assembly. It monitors conditions at its mounting point and relays that information to the control so cooling cycles run correctly and the unit maintains your selected temperature.

• Detects temperature at the sensing location and sends a resistance signal to the main control
• Helps the control regulate compressor and fan operation to maintain setpoint
• Failure can lead to poor cooling performance, short cycling or long run times
• May trigger sensor-related error codes or prevent the unit from reaching the set temperature

• Disconnect power before servicing and allow components to cool
• Access the sensor, noting wire routing and connector orientation
• Release the retainer/clip, avoid pulling on wires, and transfer any insulation or clips from the original part if present
• Route the harness away from sharp, hot, or moving parts; fully seat the connector, reassemble, and test operation

The Drain Pump Assembly is an OEM part for LG washing machines. It is responsible for pumping water out of the washing machine tub at the end of each cycle.

Causes of a bad drain pump can include motor failure, blockages in the pump's internals, cracks or fractures in the plastic body, or damaged impeller.

Symptoms of a bad Drain Pump include:

• Water not fully draining out after cycles
• Pump making strange noises when attempting to drain
• Standing water or flooding inside the washing machine

This OEM LG part is also compatible with some Kenmore models.

This multi-connector harness is the replacement wire assembly that links the appliance's control board to multiple components so signals and power flow correctly. Installing the correct harness restores reliable electrical connections and control response. What it does:

• Routes power and signal between the control board and connected components using multiple color-coded wires and connectors
• Replaces damaged, burnt, or frayed wiring that can cause intermittent operation or failure to start
• Prevents short circuits and poor connections that produce error codes or erratic performance
• Maintains correct connector pin layout for proper component communication

• One multi-connector harness (single assembly)

• Disconnect power before beginning work to avoid shock or damage
• Verify connector orientation and full seat on both ends; do not force mismatched plugs
• Inspect mating connectors and terminals for damage or corrosion before installation

This genuine power cord assembly restores safe electrical connection to your appliance by replacing a damaged or worn power lead. Durable wiring and molded connectors help ensure a reliable feed for normal operation. What it does:

• Replaces a faulty or damaged power lead to restore power flow to the appliance
• Provides a secure, molded connection between the appliance and household power
• Can stop symptoms like no power, intermittent power loss, or tripped breakers caused by a compromised cord
• Helps eliminate loose or exposed wiring that can cause arcing or electrical smell

• Disconnect appliance from power before inspecting or replacing the cord.
• Match connector orientation and seating; secure strain relief and routing per appliance harness.
• Inspect mounting points and strain relief; do not use if connectors or wiring show damage.

This softener cap seals and directs fabric softener within the washer dispenser to prevent leaks and ensure proper dispensing. Replacing a damaged cap restores correct softener flow and helps avoid dispenser drips or residue buildup. What it does

• Seals the fabric softener compartment to prevent leaks during fill and agitation
• Directs softener into the wash at the correct cycle, helping prevent early-release or pooling
• Reduces dispenser residue and clogs caused by cracked or warped caps
• Commonly replaced when the cap is cracked, missing, or no longer forms a proper seal

• One softener dispenser cap as shown

• High-level replacement — remove the dispenser assembly cover before swapping the cap
• Power off and disconnect the washer before servicing to avoid electrical or mechanical injury
• Handle small plastic parts carefully to avoid damage; test dispenser operation after reassembly

This complete door assembly replaces a damaged or broken appliance door to restore proper sealing, closing and appearance. It's a full outer door unit that mounts in place of a worn or cracked door to help the appliance operate safely and look finished. What it does

• Replaces a cracked, dented or warped outer door that prevents proper closing or sealing
• Restores proper latch alignment and helps stop air or heat loss from the appliance cavity
• Fixes cosmetic damage like scratches, dents or broken trim around the door opening
• Reduces noise and vibration caused by a loose or damaged door assembly

• One complete door assembly

• Disconnect power and any fuel supply before starting work; follow manufacturer safety procedures
• Handle the door and glass with care; support weight during removal and installation to avoid dropping
• Check hinge alignment and fastener torque; tighten to manufacturer spec if available
• If the door contains glass or wiring (switches, lights), verify connections and seals before restoring power

This replacement siphon cap seals the siphon/drain connection to help prevent leaks and keep the appliance's drainage operating as intended. It restores a watertight seal and helps reduce drips or odors caused by a compromised cap. What it does:

• Seals the siphon/drain connection to prevent water leaks and drips
• Helps maintain proper drainage by preserving the siphon's seal
• Reduces the chance of odors from slow or exposed drains
• Replaces a worn, cracked, or missing siphon cap to restore normal operation

• One siphon sealing cap

• Turn off and unplug the appliance and shut off the water supply before servicing
• Remove the old cap and clean the mating surface before installing the new cap
• Press the cap into place until fully seated; ensure a snug, leak-free fit

This Hinge bracket secures the appliance door to the cabinet, providing a stable pivot so the door opens and closes smoothly. Replace a damaged bracket to restore proper door alignment and operation. What it does:

• Anchors the door hinge assembly to the cabinet or frame so the door pivots correctly
• Prevents door sagging, misalignment, and uneven gaps that can affect sealing
• Stops clicking, scraping, or binding caused by a cracked or worn bracket
• Helps the door latch and close securely for normal operation

• One hinge bracket

• Disconnect power and empty the door before starting any repair
• Support the door while removing hinge fasteners to avoid dropping or damage
• Use the same mounting screws; inspect and replace any stripped or damaged fasteners