Wmh31017fs-0 Parts

This lamp cover is the replacement lens that protects and diffuses your oven's interior light, restoring even illumination while keeping the bulb shielded from heat and food residue. It helps maintain safe, usable oven lighting. What it does:

• Protects the oven light bulb from splashes, crumbs and direct contact.
• Diffuses the bulb for more even interior illumination.
• Replaces a cracked, cloudy, melted or missing lens that can cause dim or exposed lighting.
• Fits over the lamp housing to restore the oven's normal light appearance and function.

• Disconnect power to the appliance before starting and allow the oven to cool completely.
• Handle the cover carefully—wear gloves to protect from sharp edges or broken glass.
• Remove any retaining screws or clips, swap the old cover for the new one, then secure the retainer.
• After installation, restore power and replace the bulb if issues persist.

This inlet cover protects and conceals the appliance's inlet area, keeping wiring and connections secure and helping prevent debris from entering. It restores a clean, safe inlet opening and supports proper component alignment. What it does:

• Shields the inlet opening and nearby connections from dust and debris
• Holds inlet components in position to reduce movement and wear
• Helps prevent snagging or accidental contact with inlet wiring or fittings
• Visible damage or a loose/misaligned cover can expose connections and lead to leaks or electrical issues

• One inlet cover

• Disconnect power and shut off water supply before beginning work
• Remove the appropriate access panel or trim to reach the inlet area
• Replace cover, securing with the original screws or clips; do not overtighten
• Inspect nearby gaskets, fittings and wiring while replacing the cover

This fixed-temperature thermostat is a temperature-sensing safety switch that opens at a set limit to help prevent overheating and protect heating systems. Use it to restore proper thermal cutoff control in affected appliances. What it does:

• Senses internal temperature and opens the circuit when a set limit is reached to stop heating
• Acts as a high-limit/thermal cutoff to prevent overheating and potential damage
• Can restore normal heating control when a faulty limiter causes shutdowns or safety trips
• Common symptom link: appliance heater runs erratically, will not heat, or heats continuously and may trip safety circuits

• One fixed-temperature thermostat

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle and test with care; verify continuity with a multimeter to confirm failure before replacing
• Follow the appliance service manual and wiring diagrams for correct location and wiring

This refrigerator water filter cartridge replaces the installed filter to help restore clear, better-tasting water and improve ice quality. It's a direct-fit replacement designed for compatible Whirlpool refrigeration systems. What it does:

• Filters water to reduce common impurities that can affect taste and clarity
• Helps improve the quality of ice produced by the refrigerator
• Can resolve symptoms like cloudy water, off-taste, or reduced water flow from the dispenser
• Restores proper filtration performance when the original filter is expired or clogged

• Follow the refrigerator manufacturer's instructions for removal and installation.
• Run and discard the recommended amount of water after installation to flush the system before use.
• Turn off the water supply and disconnect power if required by your model before servicing.
• Inspect the new filter for damage; do not use a damaged filter.

This thermostat is a temperature-sensing limiter that helps regulate and limit appliance heat for safe operation. It restores proper temperature control so the appliance runs within designed operating ranges. What it does:

• Senses internal temperature and opens/closes the circuit to control heating
• Prevents overheating by interrupting power when temperatures exceed safe limits
• Commonly used in dryers and ranges as a safety/temperature control component

• Disconnect power (and gas, if applicable) before servicing to avoid shock or fire
• Handle the sensor and terminals carefully to avoid damage; avoid bending the sensing element
• One thermostat temperature limiter

The Door Assembly is an OEM part for Whirlpool microwaves. It is responsible for safely enclosing the microwave cavity and providing access to cook food. 

Causes of a bad door assembly can include wear and damage over time, such as dents, scratches, or cracks that compromise the integrity of the enclosure. Hinges or latches may become loose or malfunctioning.

Symptoms of a bad door assembly include:

• Difficulty opening or closing the door 
• Door not shutting or latching properly
• Leaks or excessive heat escaping from the door seams
• Damage or deterioration visible on the exterior door surface

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This capacitor stores and releases electrical energy to help an AC motor start and run smoothly. Replacing a weak or failed capacitor can restore reliable motor operation and reduce humming, no-start, or stall conditions.

• Provides the phase shift and starting torque an induction motor needs to start
• Helps the motor reach and maintain proper speed under load
• Common symptoms of a failing capacitor: motor hums but won't start, intermittent starts, slow or stalled rotation, or frequent thermal trips
• Visible clues may include a swollen case or leaking residue

• Disconnect power to the appliance before servicing; verify no voltage is present
• Capacitors can retain a charge—discharge safely before handling
• Note wire positions; move leads to the new capacitor one at a time and ensure snug terminal fit
• Reuse the original bracket/clip if applicable and secure the capacitor to prevent vibration

This grill vent is the front vent trim that channels heat and smoke away from the cooktop and oven cavity, keeping internal components protected and helping your range vent properly during broiling and baking. What it does:

• Directs exhaust and heat away from the oven cavity to help maintain proper airflow.
• Protects underlying components and internal wiring from direct heat and food debris.
• Replacing a damaged vent can reduce smoke buildup and improve overall oven performance.

• Disconnect power to the appliance (and gas if applicable) before starting any work.
• Use care handling edges; trim pieces can be sharp.
• Removal/installation typically involves removing fasteners or clips—keep hardware handy for reassembly.

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This transformer provides the low-voltage power needed by the appliance's control and user-interface circuits so systems like the dispenser, ice maker, or control board can operate reliably. What it does:

• Steps down mains power to low-voltage power for control boards and user-interface components
• Restores power to dispensers, ice makers, timers or control modules that have lost low-voltage supply
• Commonly replaced when control circuits are unresponsive, displays are blank, or dispenser functions fail
• Matches OEM function for direct replacement of the failed transformer

• One replacement transformer

• Disconnect all power to the appliance before starting work to avoid shock hazard
• Handle wiring connections carefully; make secure electrical connections and restore grounding

The Fan Motor is an OEM part for Whirlpool microwaves. This fan motor is responsible for circulating air through the venting system. It works to evacuate fumes, smoke, and odors from the cooking area and direct them outside through the vent hood.

Causes of a bad fan motor can include excess dust or debris buildup hindering performance, bearing wear over time, or failure of electronic motor components.

Symptoms of a bad fan motor include:

• Inadequate or no air flow from the vent hood
• Strange noises coming from the vent system
• Reduced hood lighting levels
• Overheating or burning smells detected from the cooking surface or vent hood

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replacement plate that restores fit and finish for compatible Whirlpool appliances. Install to replace a cracked, warped, or cosmetically damaged plate and help maintain proper component alignment and appearance. What it does:

• Replaces a damaged or worn plate to restore the appliance's original coverage and appearance.
• Helps prevent gaps where food, grease, or debris can collect around the affected area.
• Maintains proper alignment and support for adjacent parts that rely on the plate for mounting or spacing.

• Disconnect power to the appliance before beginning any repair.
• Use basic hand tools and follow the OEM diagram for correct orientation and fastener locations.
• Inspect mounting hardware and any gaskets; replace separately if worn or damaged.

This grill vent is the outer vent trim that restores proper airflow and appearance for your appliance. It replaces a cracked, broken or missing vent to help keep the oven or range exterior neat and allow normal ventilation. What it does:

• Covers and protects the appliance vent opening while directing air flow
• Replaces damaged or melted vent trim that can detract from appearance
• Helps keep debris and large particles out of the vent path
• Visible exterior part—symptoms include cracks, warping, discoloration or gaps at the vent area

• Disconnect power to the appliance before beginning any work
• Typically installs with simple clips or screws; retain all fasteners and trim pieces
• Inspect surrounding trim and seals for damage and replace if needed

Color: Black