Wmh32519hz-1 Parts

This factory support stabilizes and positions its mating assembly so it stays secure and aligned during use. Replacing a worn or broken support helps restore proper fit and prevents looseness or shifting that can affect performance. What it does

• Provides structural support and correct positioning for the related assembly
• Helps prevent wobble, sagging, rattling, or misalignment
• Typical failure signs: visible cracks, broken/missing tabs, or a loose fit
• Can help resolve components not staying in place or moving unexpectedly

• 1 support

• Disconnect power to the appliance before servicing
• Access the support location and note the original orientation
• Transfer and reuse any original mounting hardware your model uses
• Seat the new support fully and verify a secure fit before restoring power

This Light Housing secures and protects the interior lamp assembly, helping keep the compartment safely illuminated. Replace a cracked or heat-damaged housing to restore a stable bulb fit and consistent lighting performance. What it does:

• Provides a stable mount for the interior light bulb/socket
• Shields nearby wiring and components around the lamp area
• Helps position the light for proper illumination inside the compartment
• Common signs of wear: cracked or melted housing, loose bulb fit, lens/cover won't stay attached, intermittent lighting from a poor physical connection

• 1 light housing

• Disconnect power to the appliance before servicing
• Remove the lens/cover and bulb, then unfasten the damaged housing
• Transfer the existing socket, wiring, and any hardware from the old housing as needed
• Reinstall the housing, replace bulb/cover, restore power, and test the light

The Interlock Switch is an OEM part for Whirlpool microwaves. It monitors the position of the microwave door and signals to the control board whether it is safe to operate. 

Causes of a bad interlock switch can include normal wear over time as the switch contacts open and close frequently with door usage. Lubricant breakdown or damage to wires/connectors may also cause failures.

Symptoms of a faulty interlock switch include:

• The microwave running with the door open 
• Failure to start the microwave regardless of door position
• Inoperative door or faulty door latching 

Replacing with this genuine OEM switch restores an essential safety feature. With accurate door monitoring, microwave energy transmission only occurs when intended.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This Whirlpool Microwave Interlock Switch is an OEM part specifically compatible with various Whirlpool microwave models. This safety component ensures that the microwave operates only when the door is securely shut, thereby preventing accidental exposure to microwave energy. 

The failure of microwave interlock switches is often due to mechanical wear, electrical faults, or alignment issues. A defective interlock switch can result in the microwave not starting, running with the door open, or displaying erratic behavior, all of which are serious safety concerns.

Symptoms of a failing microwave interlock switch include:

• The microwave does not start or operate intermittently.
• The appliance runs while the door is open.
• Sudden stopping of the microwave during operation.
• Unusual sounds when the microwave door is opened or closed.
• The control panel is unresponsive or behaves irregularly with the door closed.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

This is the appliance's main power cord. It delivers household electricity to the unit so it can operate safely and reliably.

• Supplies AC power from the wall outlet to the appliance's internal wiring
• A damaged or failed cord can cause no power, intermittent power, or tripped breakers
• Replacing a worn cord can restore consistent power and improve safety

• Unplug the appliance and turn off power at the breaker before service
• Route and secure the cord to prevent pinching or abrasion

Color: Stainless

This inlet cover protects and conceals the appliance's inlet area, keeping wiring and connections secure and helping prevent debris from entering. It restores a clean, safe inlet opening and supports proper component alignment. What it does:

• Shields the inlet opening and nearby connections from dust and debris
• Holds inlet components in position to reduce movement and wear
• Helps prevent snagging or accidental contact with inlet wiring or fittings
• Visible damage or a loose/misaligned cover can expose connections and lead to leaks or electrical issues

• One inlet cover

• Disconnect power and shut off water supply before beginning work
• Remove the appropriate access panel or trim to reach the inlet area
• Replace cover, securing with the original screws or clips; do not overtighten
• Inspect nearby gaskets, fittings and wiring while replacing the cover

This replaceable refrigerator water filter cartridge helps restore clear, better-tasting drinking water and ice by capturing sediment and common impurities. Designed for a quick swap to keep your fridge dispensing clean water. What it does:

• Filters sediment and particulate to reduce cloudiness in water and ice
• Helps improve taste and odor commonly associated with older filters
• Restores normal water flow and delivery when a clogged filter causes slow dispensing
• Supports routine maintenance to help prevent scale and buildup in the dispenser system

• Shut off the refrigerator water supply before removal to limit spills
• Follow the refrigerator manufacturer's removal/installation motion (push, pull, twist, or bayonet style)
• Flush several full glasses of water after installation to clear air and initial carbon fines
• Check for leaks at the filter and housing after restoring the water supply; discard the old filter per local regulations

This lamp cover is the replacement lens that protects and diffuses your oven's interior light, restoring even illumination while keeping the bulb shielded from heat and food residue. It helps maintain safe, usable oven lighting. What it does:

• Protects the oven light bulb from splashes, crumbs and direct contact.
• Diffuses the bulb for more even interior illumination.
• Replaces a cracked, cloudy, melted or missing lens that can cause dim or exposed lighting.
• Fits over the lamp housing to restore the oven's normal light appearance and function.

• Disconnect power to the appliance before starting and allow the oven to cool completely.
• Handle the cover carefully—wear gloves to protect from sharp edges or broken glass.
• Remove any retaining screws or clips, swap the old cover for the new one, then secure the retainer.
• After installation, restore power and replace the bulb if issues persist.

This fixed-temperature thermostat is a temperature-sensing safety switch that opens at a set limit to help prevent overheating and protect heating systems. Use it to restore proper thermal cutoff control in affected appliances. What it does:

• Senses internal temperature and opens the circuit when a set limit is reached to stop heating
• Acts as a high-limit/thermal cutoff to prevent overheating and potential damage
• Can restore normal heating control when a faulty limiter causes shutdowns or safety trips
• Common symptom link: appliance heater runs erratically, will not heat, or heats continuously and may trip safety circuits

• One fixed-temperature thermostat

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle and test with care; verify continuity with a multimeter to confirm failure before replacing
• Follow the appliance service manual and wiring diagrams for correct location and wiring

This electronic control board replaces the main console control for electric ovens and ranges, restoring responsive controls and timed cooking functions. It manages user inputs, display output, and cycle sequencing for the appliance. What it does:

• Receives commands from the touchpad/knobs and drives oven heating cycles and timers
• Controls display and indicator lights so settings and temperatures are visible
• Manages oven bake/clean modes and safety interlocks during operation
• Commonly used when the oven won't heat, displays are blank or show errors, or controls are unresponsive

• One electronic control board

• Disconnect power to the appliance before starting any repairs to avoid shock
• Handle the board by its edges and avoid touching components; wear anti-static protection if available
• Some models require removing the control panel or console to access the board; keep screws and connectors organized

This thermostat is a temperature-sensing limiter that helps regulate and limit appliance heat for safe operation. It restores proper temperature control so the appliance runs within designed operating ranges. What it does:

• Senses internal temperature and opens/closes the circuit to control heating
• Prevents overheating by interrupting power when temperatures exceed safe limits
• Commonly used in dryers and ranges as a safety/temperature control component

• Disconnect power (and gas, if applicable) before servicing to avoid shock or fire
• Handle the sensor and terminals carefully to avoid damage; avoid bending the sensing element
• One thermostat temperature limiter

This capacitor stores and releases electrical energy to help an AC motor start and run smoothly. Replacing a weak or failed capacitor can restore reliable motor operation and reduce humming, no-start, or stall conditions.

• Provides the phase shift and starting torque an induction motor needs to start
• Helps the motor reach and maintain proper speed under load
• Common symptoms of a failing capacitor: motor hums but won't start, intermittent starts, slow or stalled rotation, or frequent thermal trips
• Visible clues may include a swollen case or leaking residue

• Disconnect power to the appliance before servicing; verify no voltage is present
• Capacitors can retain a charge—discharge safely before handling
• Note wire positions; move leads to the new capacitor one at a time and ensure snug terminal fit
• Reuse the original bracket/clip if applicable and secure the capacitor to prevent vibration

This grill vent is the front vent trim that channels heat and smoke away from the cooktop and oven cavity, keeping internal components protected and helping your range vent properly during broiling and baking. What it does:

• Directs exhaust and heat away from the oven cavity to help maintain proper airflow.
• Protects underlying components and internal wiring from direct heat and food debris.
• Replacing a damaged vent can reduce smoke buildup and improve overall oven performance.

• Disconnect power to the appliance (and gas if applicable) before starting any work.
• Use care handling edges; trim pieces can be sharp.
• Removal/installation typically involves removing fasteners or clips—keep hardware handy for reassembly.

This outer wrapping assembly is the coated black outer layer that fits around the dryer drum to protect the drum and improve airflow. It restores proper drum coverage and helps reduce rubbing, noise, and fabric snags. What it does:

• Replaces worn or damaged drum outer wrap that can cause rubbing or scraping noises
• Provides a smooth, protective surface that helps prevent clothes from catching on rough drum edges
• Helps maintain proper drum clearance and airflow for consistent drying performance
• Restores the dryer's appearance with a black, coated finish

• Disconnect power (and gas supply if applicable) before beginning any repair
• Access the drum per the dryer's service instructions; remove the drum to replace the outer wrapping
• Handle edges carefully and use gloves to avoid cuts; align the wrap evenly before securing

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts