Woc54ecoaw02 Parts

Restore a flat, secure cooking surface with this replacement oven rack. Replace a bent, rusted, or missing rack so pans sit level and slide smoothly for more consistent baking, roasting, and broiling.

• Provides a sturdy platform for cookware and adjusts to multiple rack positions
• Slides on the oven's side rails for easy access to dishes
• Replace if wires are bent/warped, plating is flaking or rusty, the rack is unstable, or it no longer glides smoothly
• Can help resolve uneven results caused by a sagging or improperly seated rack

• Disconnect power and allow the oven to cool completely before installing
• Align the rack's side rails with the oven support guides and keep it level
• Slide fully inward until the rear stops engage; verify it's seated evenly on both sides
• Clear debris from support guides for smooth operation; avoid harsh abrasives on plated surfaces

Restore a safe, efficient oven door with this inner glass panel. It replaces the heat-resistant liner on the inside of the door, helping retain heat and keep the viewing window clear during cooking. What it does:

• Forms the inner layer of the oven door window and helps insulate the oven cavity
• Maintains a clear interior-facing surface for viewing food
• A damaged panel can cause heat loss, temperature fluctuations, or poor visibility through the door window
• Replace if the glass is cracked, shattered, chipped, or permanently hazy/etched

• 1 inner oven door glass panel

• Disconnect power at the breaker and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; glass edges can be sharp
• Remove the door and place it face down on a protected surface; follow model-specific steps to access the inner pane
• Transfer any retainers/brackets as needed and tighten hardware evenly without overtightening

This door interlock assembly mounts behind the microwave's front panel and aligns the latch and safety switches. Replacing a worn interlock restores reliable door detection so the microwave only starts when the door is fully closed.

• Holds and actuates the internal door safety switches
• Maintains precise latch alignment to prevent false "door open" signals
• Ensures the microwave will not run with the door open for safety
• Common symptoms: won't start, requires pressing on the door to run, stops when the door is jostled, intermittent "door" message

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a charge.
• Access typically requires removing the outer cabinet and control panel.
• Position switches correctly in the holder per your service manual and verify smooth latch engagement.
• After reassembly, the unit only operates with the door fully closed.

This interlock is the door switch bracket used in select microwaves. It aligns and supports the door-switch mechanism so the oven runs only when the door is fully closed, restoring safe, consistent door-sensing and start/stop performance.

• Holds and aligns the door switches and latch levers inside the cabinet
• Ensures the microwave stops when the door opens and runs only when fully closed
• Common fixes: won't start unless the door is pressed, stops when the door is moved, or shows a door-related door message
• Replaces cracked, warped, or loose interlock brackets that cause intermittent operation

• Disconnect power before servicing; microwaves contain high-voltage capacitors
• Access is typically behind the control panel; note each switch's orientation and wiring before transfer
• Transfer existing switches and hardware to the new bracket as configured for your model
• Use caution around sharp cabinet edges

The Oven Door Handle is an OEM part for Whirlpool wall ovens. This handle allows for easy, safe opening and closing of the oven door during use. 

Causes of a bad door handle can include wear and tear from repetitive use over time, damage from improper cleaning methods, or cracks/breaks from accidental impact.

Symptoms of a bad oven door handle include:

• Loose, wobbly, or unstable door grip 
• Cracks or splits in the handle material
• Handle completely detached from door

This replacement handle is also compatible with select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall oven models.

This replacement microwave door restores a secure seal and a clear view into the cavity. Replace a cracked, bent, or misaligned door to help the interlocks engage properly so the oven can start and operate safely.

• Provides the door assembly used to open/close the microwave, with viewing window and latch hooks that actuate the door switches
• Seals the cavity perimeter via the choke to help contain microwave energy when latched
• Common symptoms include: door won't close or latch, oven won't start or shows a door-ajar error, or visible damage to the door frame or glass
• Helps resolve issues caused by a warped/bent door, broken trim, or loosened components

• Disconnect power before servicing; do not remove the microwave's outer cabinet
• Support the door, lift it off the hinges, and protect hinge springs and latch areas from damage
• Transfer any model-specific trim or hardware from the original door if required
• Align hinges and latch hooks; verify the door closes flush and latches securely.

This electronic control board manages the oven's user interface and timing functions so the range responds correctly to button presses, displays information, and controls bake/ broil cycles. It restores control for normal cooking operations. What it does:

• Receives input from the touchpad/knobs and sends commands to the oven's heating and timing systems
• Controls display, clocks, timers and cycle settings so the oven operates as selected
• Helps regulate bake/broil cycles by signaling relays or the oven ignitor
• Common symptom when failing: blank or unresponsive display, controls that don't start cycles, or persistent error codes

• One electronic control board

• Disconnect power to the appliance at the breaker before servicing
• Handle the board carefully to avoid ESD damage and avoid touching circuit traces
• Verify connector seating and wire harness routing during reassembly

This replacement door hinge restores smooth, stable door movement and proper alignment. Replacing a worn hinge helps the door open and close correctly so the appliance seals as designed and operates safely.

• Provides the pivot point for opening and closing the door
• Helps maintain door alignment for a consistent, reliable seal
• Replaces a bent, loose, or worn hinge that affects door operation
• Common symptoms: door sags, won't close fully, pops open, binds, or squeaks

• Disconnect power; turn off gas or water supply before servicing
• Support the door during removal and installation to prevent damage or injury
• Compare the new hinge to the original and transfer any reusable hardware
• After installation, check door alignment and closure; adjust per your model's service instructions

A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:

• Provides a fixed-diameter shoulder for pivots, spacers, or mounting points in assemblies.
• Holds panels and moving components at the correct distance to prevent binding or friction.
• A missing or worn shoulder screw can cause misalignment, rattling, or loose parts during operation.
• Used where a smooth-bearing surface and controlled clearance are required between parts.

• Disconnect power to the appliance (unplug or shut off breaker) before servicing.
• Handle small fasteners carefully to avoid dropping into assemblies; magnetic pickup tools can help.
• Start threads by hand to avoid cross-threading; tighten snugly but avoid overtightening.

This factory window pack assembly creates the sealed, insulated glass window in your oven door. It restores a clear view into the cavity and helps the appliance hold temperature when the original window is broken, cloudy, or damaged.

• Forms the sealed, multi-pane window within the oven door
• Helps contain heat and maintain consistent baking temperatures
• Restores visibility into the oven cavity
• Common symptoms: cracked/shattered glass, fogging or streaks between panes, rattling glass, heat escaping near the window area

• Disconnect power and allow the oven to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass vertically and support the edges
• Door removal and partial disassembly are typically required; keep screws and trim organized
• Transfer any reusable brackets/insulation per your model's service information

This Frame-Glass is the outer glass panel for the oven door, restoring a clean appearance and helping retain heat while keeping the oven cavity visible. It replaces damaged, cracked, or chipped outer door glass. What it does:

• Provides the outer glass surface of the oven door for safe viewing of food while cooking
• Helps maintain oven heat and improve energy containment when the door is intact
• Replaces cracked, chipped, or shattered outer door glass that can affect appearance and safety
• Restores a sealed, clean-facing surface for the door assembly

• Disconnect power to the appliance and allow the oven to fully cool before beginning
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires removing the oven door and detaching trim/fasteners; keep track of screws and clips

This hex-head sheet metal screw secures appliance panels, brackets, and trim for a tight, rattle-free fit. Replace missing or stripped fasteners to keep covers and components firmly in place and restore proper alignment.

• Fastens sheet-metal parts, brackets, and trim using a hex drive
• Replaces worn, rusted, missing, or stripped screws
• Helps reduce vibration and rattling from loose panels
• Common signs you need this fastener: head or threads stripped, screw won't tighten, panel or handle coming loose

• Unplug the appliance before service; turn off water supply if working near water lines
• Use the correct nut driver or socket to avoid rounding the head
• Replace one fastener at a time to maintain alignment; do not overtighten
• Match screw type/length to the original location as specified by the manufacturer

Color: Stainless Steel
The Outer Door Glass is an OEM part for Whirlpool wall oven models. This outer glass pane allows for viewing of foods inside without compromising temperature retention.

Causes of a bad outer door glass may include cracks, chips or fractures developing from repeated exposure to thermal stresses and door slamming. Wall ovens experience high heat fluctuations which can accelerate normal wear over time.

Symptoms of a bad outer door glass include:

• Inability to maintain interior temperatures
• Excessive heat loss causing inefficient cooking
• Safety issues from exposed hot edges or broken shards
• Reduced visibility making it difficult to check food doneness

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This broiler pan restores a sturdy broiling surface in your oven. It holds food for high-heat broiling while the lower tray catches drippings to help reduce smoke and keep the oven cavity cleaner.

• Provides a durable surface for broiling under the broil element or flame
• Collects grease and juices beneath the food during high-heat cooking
• Replaces pans that are missing, warped, chipped, or heavily rusted
• Helps cut down on smoke and mess from burnt-on residue on a damaged pan

• Allow the oven to cool completely before handling
• Slide the pan onto the appropriate rack position per your model's instructions; no tools required
• Use oven mitts—surfaces and edges can be hot after broiling
• If your model uses a separate broiler grid or rack, position it on top of the pan before cooking

This replacement rack restores a stable, level surface for loading items inside your appliance. Replace a damaged or worn rack to keep items secure during operation and maintain smooth, reliable use.

• Provides a sturdy surface to support cookware or dishware during operation
• Maintains proper spacing and alignment inside the cavity
• Interfaces correctly with rails/supports for easy loading and removal
• Replace if wires/tines are broken, coating is rusting, or the rack is bent or unstable

• Disconnect power at the breaker; shut off water supply if applicable
• Remove the old rack carefully, noting orientation and any stop clips
• Transfer any reusable accessories (clips, rollers, tine rows) from the old rack if applicable
• The new rack seats/moves smoothly before returning the appliance to service