Wrs586fdlwoo Parts

This small bushing fits over the hinge cam to guide the door's swing. Replacing a worn thimble restores smooth movement and alignment so the door opens and closes consistently and helps maintain a proper seal. What it does:

• Provides a low-friction bearing surface between the hinge pin and cam
• Helps control door swing and detent/self-close action
• Supports proper door alignment to reduce rubbing or sagging
• Symptoms may include popping/clicking, grinding, binding, uneven closing, or a door that doesn't fully close

• 1 door hinge cam thimble

• Disconnect power and remove items from the door before servicing
• Support the door; remove hinge cover/fasteners and lift the door off the hinge
• Replace the thimble on the hinge/cam, matching the original orientation and fully seating it
• Inspect the mating cam and hinge surfaces; replace worn parts as needed and verify gasket seal after reassembly

Thimble cam that secures and guides the dryer door latch assembly, helping the door close and stay latched so the appliance can run safely and reliably. Replaces worn or damaged door cam components. What it does:

• Engages the door latch/strike to keep the door closed during cycles.
• Helps maintain proper door alignment so the lid/door seals and latches correctly.
• A worn or broken cam can cause the door to hang, fail to latch, or prevent the dryer from starting.
• Works as the mechanical interface between the door and latch assembly.

• Disconnect power (and shut off gas supply on gas models) before servicing.
• Access typically requires removing the dryer door trim or access panel.
• Inspect the latch, strike, and mounting hardware; replace any worn or damaged fasteners when installing the new cam.

This axle roller is the replacement support shaft that lets the appliance's rotating assembly turn smoothly and quietly. Installing a new axle roller corrects wobble and reduces grinding or squealing caused by a worn shaft. What it does:

• Supports the rotating drum or rack so it spins freely and stays aligned
• Helps prevent metal-to-metal contact that causes loud noise or scraping
• Stops uneven rotation and vibration that can lead to further wear
• Restores smooth operation when an original axle is bent, worn, or broken

• Disconnect power (and gas, if applicable) before starting any repair
• Access location and removal steps vary by model; follow the OEM service manual or diagram
• Inspect related parts (pulleys, idler, glides, bearings) and replace if they show wear
• Use basic hand tools; keep fingers and loose clothing clear of moving parts during testing

The cover-unit protects the appliance's control console and provides a finished appearance. It shields buttons, knobs and internal control components from dust, moisture and incidental damage so controls stay usable and the cabinet looks complete. What it does:

• Covers and protects the control console and the underlying control assembly
• Helps prevent debris and moisture from reaching buttons, switches and electronic components
• Restores the appliance's finished look when the original cover is cracked, broken or missing
• Keeps controls stable and reduces the chance of accidental contact or damage

• Disconnect power before servicing to avoid shock or injury
• Remove any trim or console fasteners before replacing the cover
• Handle carefully to avoid scratching the finish; use proper fasteners and align tabs during reassembly
• If controls or wiring are exposed or damaged, inspect wiring and control components.

Color: Grey

Color: Black

This is the lower front grille for select appliances. It finishes the base opening and helps channel airflow to the condenser area while protecting components from bumps and debris.

• Covers the lower front opening and provides a clean, finished look
• Helps direct cooling airflow to the condenser compartment
• Shields components from minor impacts and debris
• Common signs it needs replacement: cracked or missing grille, broken mounting tabs, grille won't stay attached, rattling from a loose or damaged panel

• Disconnect power before servicing; use proper PPE
• Remove existing fasteners or release tabs, then pull the old grille straight off
• Align the new grille and secure with the original screws/clips as configured
• Do not overtighten fasteners; ensure even engagement of all tabs

This thermistor cover shields and positions the refrigerator's temperature sensor so it reads cabinet air accurately. Replacing a cracked or missing cover helps restore stable temperatures and normal cooling performance.

• Holds the thermistor in place and shields it from direct airflow for accurate temperature sensing
• Helps prevent erratic temperatures, overcooling/undercooling, or long run times caused by an exposed sensor
• Commonly replaced when the original cover is cracked, loose, or missing
• Supports consistent temperature control by ensuring proper sensor placement

• Disconnect power before servicing
• Remove shelves/bins as needed to access the sensor location
• Align the thermistor and seat the cover fully; engage tabs or reuse existing hardware per model
• Avoid pinching the sensor or wiring and verify the cover is snug

This inverter box is the electronic module that conditions and routes power to the refrigerator compressor, helping restore variable-speed compressor operation and consistent cooling when the inverter has failed. What it does:

• Regulates and converts power for the compressor's inverter drive to support variable-speed operation.
• Replaces a failed inverter module that can cause the compressor not to start or to run intermittently.
• Commonly used when the refrigerator runs warm, cycles abnormally, or displays inverter-related errors.
• Houses the control electronics for compressor power management.

• Always disconnect power before servicing the appliance to avoid shock.
• Access may require removing the rear or control housing panels; note wire routing and connector positions before disconnecting.
• Handle as an electronic component: protect from moisture, impact, and static discharge.

This ice door motor drives the dispenser's ice chute door, opening to let ice out and closing to seal the chute. Replacing a worn motor restores proper door movement and helps reduce warm-air leaks and frost around the dispenser.

• Opens and closes the dispenser ice door (flapper) during use
• Helps keep the ice chute sealed between dispenses to limit frost and moisture
• Failure symptoms can include the ice door not opening/closing, frost or condensation in the chute, air leakage at the dispenser, or clicking from the dispenser area

• Unplug the refrigerator and shut off water before servicing
• Remove the dispenser front panel/trim and control to access the ice door mechanism
• Note wire positions; install the new motor, transferring any levers/arms as configured on your model
• Restore power and test ice door operation before reassembly

Color: Beige

This light lens fits the refrigerator compartment and covers the interior light source to protect it and diffuse glare. Replacing a damaged or missing lens restores clean appearance and even lighting inside the fresh food section.

• Covers and shields the refrigerator compartment light source
• Diffuses light for more even illumination across shelves
• Helps keep debris and moisture away from the bulb/module
• Typical reasons to replace: lens cracked, loose, missing, warped, or discolored

• Disconnect power to the refrigerator before servicing
• Remove items/shelves as needed for access
• Release the retaining tabs, remove the old lens, and align the new lens
• Press until all tabs fully engage and the lens sits flush

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

This one-piece freezer bin is the molded drawer for the freezer compartment. Replacing a cracked or warped pan restores storage capacity and smooth sliding, keeping frozen items organized and the drawer securely seated on its rails. What it does:

• Holds and organizes frozen food within the freezer compartment
• Interfaces with slide rails for smooth opening and closing
• Replace when cracked, warped, or when mounting tabs are broken
• Common symptoms: drawer wobbles, jams, falls off rails, or won't stay seated

• One freezer bin

• Disconnect power before servicing
• Empty the freezer drawer; remove any upper basket if your model has one
• Lift the old bin off the slides; align and fully seat the new bin on the rails
• Do not force parts; verify smooth travel before reloading food

Color: White

Color: White