Wsm2700wdwcc Parts

This replacement part is a dryer clip, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This dryer clip is typically found on dryers and there are usually multiple clips on one appliance. These clips help hold the front panel in place and secure so that it does not come off during the drying cycle. A new dryer clip might be needed if the front panel of the dryer is off balance or not attached correctly. It is possible that the clips can become loose over time as the appliance is prone to shaking and vibrating. The clips are important as it keeps the dangerous parts covered. If the entire front panel can be lifted off then it is time to replace the dryer clips. These clips are sold individually even though dryers typically have more than one. This clip is a genuine OEM part.

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely

This cap stud is a small protective cover that helps secure and shield electrical or mechanical studs on appliances, reducing debris buildup and protecting connections. It provides a simple, low-cost way to maintain safe appliance operation. What it does:

• Covers and protects exposed studs or fasteners from dirt and moisture
• Helps prevent accidental contact with terminals or sharp edges
• Keeps mounting hardware in place for a neater appearance
• Can reduce corrosion risk at exposed connection points

• One cap stud

• Inspect the stud and surrounding area for damage before installing
• Push the cap onto the stud until it seats firmly; no special tools typically required
• Disconnect power to the appliance before working near electrical connections
• Replace if damaged, cracked, or loose to ensure continued protection

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

This dryer hose clip secures the exhaust hose to the dryer's cabinet for a stable, sealed connection. A small but essential fastener, it helps keep the vent attached so airflow is directed out of the appliance. What it does

• Fastens the exhaust/vent hose to the dryer cabinet to maintain a secure connection.
• Helps reduce air leaks at the hose-to-cabinet joint that can cause reduced venting efficiency.
• Prevents the hose from slipping off during operation, which can cause vibration or rattling.
• Keeps the vent path aligned to reduce lint buildup at the connection point.

• One dryer hose clip.

• Disconnect power (unplug electric or shut off gas and unplug) before servicing the dryer.
• Remove the dryer vent hose and position the clip over the hose and cabinet fitting; secure per OEM orientation.
• Tighten only to snug — avoid over-tightening which can deform the hose or cabinet inlet.
• Inspect the hose and cabinet inlet for damage; replace damaged components to ensure a proper seal.

This tub seal assembly keeps the washer's inner tub sealed around the drive shaft to help prevent water leaks and contain wash water. It replaces a worn or damaged tub seal to restore a watertight fit. What it does

• Seals the gap between the inner tub and the transmission/drive shaft to reduce leaks
• Helps prevent water from entering the transmission area and causing damage
• Commonly replaced when you notice water on the floor or pooling under the washer
• Used when the existing seal is cracked, torn, or excessively worn

• One tub seal assembly

• Disconnect power and shut off water before starting any repair
• Replacement typically requires partial disassembly of the washer (cabinet or front panel removal) and access to the tub/transmission area
• Inspect shaft and surrounding surfaces for wear or damage and clean mounting surfaces before installing the new seal

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

This light hole plug seals the unused drum-light opening in the dryer cabinet. Replacing a missing or brittle plug helps contain lint, limit drafts, and protect internal components around the opening.

• Covers the factory light opening when no drum light is installed
• Helps maintain proper cabinet airflow and lint containment
• Shields the opening from dust and moisture
• Replace if the plug is missing, cracked, hardened, or won't stay seated

• Disconnect power before servicing
• Access the light-hole location per your model's service instructions
• Press the plug fully into the hole until seated flush
• Ensure no wires or components are pinched around the opening

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal