Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Hardware washer distributes load under fasteners to prevent loosening and reduce vibration. Replace when missing or damaged to restore secure fit.
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running. Read more
Suspension skate plate mounts under the washer drum to support the tub assembly. Replace if cracked, broken, or warped. Includes suspension pads.
Washer won't spin or makes noise during spin? This clutch spring cap maintains proper tension in the drive assembly. Quick 5-minute DIY repair.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Fix a washer that won't switch water temperatures or cycles properly. This rotary switch controls temperature selection and cycle progression.
Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.
Added the extension drainage hose Read more
Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.
Purchased water inlet valve and new hot and cold water hoses. Unscrewed about 5 screws that were holding the top of the washer in place then slide the top forward and up. Released the control top it popped off no screws. Disconnected the wires attached and unscrewed 2 screws holding the valve in place the popped that off. Popped in a new valve and repeated the process in reverse. Boom done! Very simple works like new! Read more
Secures the control panel to the washer cabinet. Replace if your console strap is cracked, broken, or missing, causing the control panel to sag or shift.
Gray acrylic spray paint for coating worn or chipped dryer drum interiors. Restores the protective finish when the original coating is scratched or flaking.
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do Read more
Ground screw secures transmission housing and console components in washers. Replaces missing, stripped, or corroded screws. 10-24 x 3/8 inch fastener.
Replaced timer control unit, first time doing this. Read more
Water fill hose connects your washer to the water supply. Replace if cracked, kinked, or leaking. Includes 2 hoses, 5 feet each, with washers installed.
We found the pump online at AppliancePartsPros.com for our model of Maytag. When we found the part, there was a video posted that was for our exact pump and washer. After watching it, we called Appliance Parts Pros to verify the part. The customer service representative was incredibly helpful and confirmed our diagnosis. We ordered the pump as well as hoses and clamps in case we needed them. We ordered them overnight delivery and the customer service rep said that we might not receive it... Read more
Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.
Washer won't spin or vibrates excessively? This spring damper assembly cushions the drum during spin cycles, reducing vibration for smooth operation.
Secures your washer's drain U-bend to prevent leaks and keep plumbing properly aligned. Simple push-fit installation takes just minutes to complete.
Added adapter and placed hose over laundry tub edge. Read more
Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.
Fixes sparking or loose motor connections causing spin issues. Replaces cracked or melted wiring harness connector. Straightforward repair, 30 minutes.