Wtw58408w0 Parts

Screw: 8-16 x 3/8 inch.

This electromechanical timer controls cycle sequencing on compatible appliances, restoring reliable timing and program advancement so the unit runs through its selected cycles correctly. What it does:

• Advances and holds program steps so the appliance completes wash/dry/heating cycles in order
• Routes power to motors, valves, and heaters per cycle settings
• Helps stop or start operations when controls are set
• Common symptom linkage: cycles don't advance, controls are unresponsive, or the unit won't start or complete a cycle

• One electromechanical timer assembly

• Disconnect power (unplug or breaker) before servicing to avoid shock or injury
• Verify wiring location and take photos before removal to ensure correct reconnection
• Handle with care; avoid dropping or exposing the timer to moisture

4 position

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Replacement flexible hose that routes water inside your appliance, restoring secure flow and helping prevent leaks or drainage problems caused by cracked, kinked, or worn hoses. What it does:

• Directs water to and from appliance components during normal operation.
• Prevents leaks when hose walls and fittings are intact.
• Common symptom fix: visible leaks, water pooling beneath the appliance, or reduced/irregular water flow.
• Fits in-line with existing clamps and fittings to maintain proper routing.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect and replace clamps or fittings if corroded or damaged; use proper-size clamps for a secure seal.
• Route hose without sharp bends or kinks and avoid contact with hot surfaces or moving parts.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Replacement console strap that secures the appliance control panel to the cabinet, restoring stable console alignment and preventing the control panel from shifting or sagging during use for safer, neater operation. What it does:

• Secures the control console to the cabinet to prevent wobble, tilt, or separation.
• Replaces a worn or broken strap commonly causing a loose or misaligned control panel.
• Helps reduce strain on control harnesses and connectors that can occur when the console moves.
• Matches OEM fit so the console remains properly seated and functional.

• Disconnect power to the appliance before beginning any repair.
• Typically accessed by removing the console or control panel; retain all screws and clips for reassembly.
• Use common hand tools (screwdriver, nut driver) and follow the model-specific service manual for exact steps.
• If wiring connectors are disturbed, verify secure connections before restoring power.

This tub ring is the replacement sealing ring that fits around the washer's outer tub to help keep the wash basket secured and reduce vibration. It restores proper sealing and alignment for reliable washer operation. What it does:

• Provides a protective seal between the inner basket assembly and the outer tub
• Helps reduce noise and vibration caused by a loose or worn tub interface
• Prevents minor rubbing or chafing between rotating parts
• Can help address symptoms like unusual noise, rubbing sounds, or movement in the wash basket

• One tub ring

• Disconnect power and water supply before starting any repair
• Basic disassembly of the cabinet or tub may be required; follow the machine's service manual
• Use proper tools and take care not to damage the tub finish or nearby components

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

The Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for properly dispensing the correct amount of laundry detergent at the appropriate time in the wash cycle. The detergent dispenser drawer is specifically designed to hold laundry detergent pods or liquid in its molded compartments.

Causes of a damaged detergent dispenser drawer can include corrosion or degraded plastic parts over time caused by repeated exposure to laundry detergents.

Symptoms of a malfunctioning dispenser drawer include:

• Improper dispensing or no dispensing of detergent during wash cycles
• Residue buildup or leaks from the dispenser area
• Drawer not opening or closing securely as intended
• Dispenser components broken, cracked, or non-functional

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This water inlet valve controls water flow to the appliance's dispenser/ice system so you get water or ice when needed. It replaces a failed valve to restore proper filling and dispensing without guessing which component is faulty. What it does

• Opens and closes to allow water into the dispenser or ice-maker when signaled
• Commonly replaced for no water, weak water flow, or ice maker not filling
• Stops water flow when the dispenser/ice cycle is complete to prevent overfill
• Works with the appliance's control and wiring harness to operate on demand

• Disconnect power and shut off the water supply before beginning work
• Confirm electrical connectors and inlet/outlet hoses are securely seated and undamaged
• Handle valve and fittings carefully to avoid kinking hoses or stripping threads