Wtw58408w0 Parts

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This replacement control knob fits stove and oven front panels and restores a secure, easy-to-use interface for setting cooktop or oven functions. It makes selecting heat or function positions simple and more reliable. What it does:

• Replaces a broken, cracked, missing, or stripped control knob used to turn temperature or function selectors
• Provides a positive grip and clear detent positions for accurate setting selection
• Helps eliminate slipping or loose knobs that prevent precise control
• Matches the original shape and mounting style for a direct push-on replacement

• Pull off the damaged knob and push the replacement onto the valve/stem until fully seated
• Unplug the appliance or disconnect power before servicing electrical or gas controls
• Ensure the knob aligns with the shaft flat or keyed slot so positions match the control panel markings
• Do not force fit; if knob does not seat, inspect the control shaft and the knob bore for damage

Color: White

Note: Bearings are only available with the gearcase assembly.

This replacement bezel is the outer trim that surrounds and protects your appliance's control panel, restoring a finished look and shielding buttons and displays from dirt and damage. It's a simple cosmetic and protective repair. What it does

• Covers and protects the control area from spills, dust and everyday wear.
• Restores a clean, finished appearance when the original bezel is cracked, scratched or discolored.
• Helps keep buttons and displays secure and properly aligned.
• Stops rattling or loose trim that can occur when the bezel is broken or warped.

• One bezel (trim) as shown.

• Disconnect power to the appliance before starting any work.
• Removal typically requires loosening a few screws or clips on the control panel; support the panel while removing the bezel.
• Handle edges carefully to avoid scratching the new trim and wear gloves to prevent cuts.

This is an outer tub for washing machines. The outer tub and holds the inner tub and makes sure water doesn't leak into the rest of the appliance. A damaged outer tub will often make loud noises and could cause leaks.When replacing the outer tub, make sure the washing machine is unplugged and the water supply is turned off. Remove the control panel before disassembling the washing machine to get access to the outer tub. Tap the drive block and disconnect the outer tub before pulling the hose free and removing the suspension springs. The new part can be installed in the new place before turning the power and water back on. This outer tub is made for use with washing machines and washer and dryer combination appliances made by Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Magic Chef, Admiral, Roper, Crosley, Inglis, and Estate. This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part.

This small mounting screw secures the appliance's timer to its bracket or control console. It replaces missing or stripped hardware to keep the timer stable, properly aligned, and operating smoothly when you turn the control knob.

• Fastens the timer assembly securely to its mounting bracket or console
• Prevents shifting and vibration that can make the control feel loose or wobbly
• Helps maintain proper alignment of the timer shaft/knob
• Ideal replacement when original hardware is missing or threads are damaged

• Disconnect power before servicing; shut off gas if applicable
• Access the control console and support the timer while removing/reinstalling hardware
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening into plastic or thin metal
• Replace screws one at a time to keep the timer aligned