Wtw8420 Parts

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This is the appliance's central electronic control (ACU). It manages cycle timing and coordinates key components so the unit operates as designed. Replacing a failed board can restore proper function and responsiveness.

• Coordinates cycle logic, timing, and power to motors, valves, pumps, and heaters
• Interprets user inputs and sensor feedback to advance cycles correctly
• Common symptoms: won't start, unresponsive controls/display, stops mid-cycle, intermittent power/resetting
• Presents error codes indicating a main control/ACU fault

• Disconnect power before service and observe ESD precautions when handling electronics
• Photograph wiring and transfer connectors one at a time to the new board
• Reuse existing mounting hardware and covers unless replacement is specified
• Some models require configuration or a service calibration after install—follow the unit's tech sheet

This bezel is a trim piece that finishes and protects the opening around a control or feature on the appliance's panel. Replacing a cracked or missing bezel restores a clean look and helps the mating control sit securely and operate properly.

• Frames the control or opening and covers raw edges for a finished appearance
• Helps keep the associated knob/button or trim aligned and seated
• Shields internal components from dust, splashes, and minor impacts
• Replace if cracked, warped, loose, or missing; symptoms can include a wobbly control, visible gaps, or cosmetic damage

• Disconnect power at the breaker before servicing; allow any hot surfaces to cool
• If applicable, pull off the knob or remove adjacent trim to access the bezel
• Release locking tabs or remove mounting screws carefully to avoid scratching the panel
• Align the new bezel with tabs/orientation marks and snap or fasten into place; reinstall parts and test

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This fresh-water nozzle assembly directs a controlled stream into the appliance during fill/dispense. Replacing a cracked or clogged nozzle restores proper flow and helps reduce splashing, misdirected spray, or dripping at the opening. What it does:

• Shapes and directs fresh water into the tub/dispenser area
• Helps prevent spray, backflow, and mess around the opening
• Common symptoms: weak or misdirected stream, dripping after fill/dispense, leaks near the opening, visible cracks or mineral buildup on the nozzle
• A kinked or brittle attached tube can restrict flow or leak

• One fresh-water nozzle assembly

• Disconnect power and shut off the water supply before servicing
• Access the nozzle area; remove necessary panels or trim
• Release retaining clip(s), disconnect tubing, and note routing before removal
• Install the new assembly fully seated; restore water/power, check for leaks, and run a test fill to flush air/debris

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

The Rotor is an OEM part for Whirlpool washers. It is responsible for rotating the drum during the wash and spin cycles. It provides the necessary power and motion to agitate and clean your clothes effectively.

A bad washer rotor can occur due to wear and tear over time or damage caused by excessive loads or foreign objects that may have entered the drum. If you notice symptoms such as a noisy or vibrating washer, the drum not spinning properly or not spinning at all, or error codes indicating motor-related issues, it may be time to replace the washer rotor.

Symptoms of a bad washer rotor include:

• Noisy or vibrating washer
• Drum not spinning properly or not spinning at all
• Error codes indicating motor-related issues

Restore your washer by replacing the faulty or worn-out washer rotor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Color: Grey

The Lid Lock Bezel is an OEM replacement part for Whirlpool washing machines. 

Symptoms of a need to replace the bezel include:

• Cracks, discoloration, or visible damage to the bezel
• Looseness or detachment of the bezel from the panel

Causes of a damaged or worn bezel can include accidental impacts, exposure to cleaning chemicals, or general wear and tear over time.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models.

This washer drain hose routes wastewater from the drain pump to your home standpipe or laundry tub. Replacing a cracked, kinked, or clogged hose helps stop leaks and restores proper draining so cycles complete reliably.

• Directs discharge water from the washer to the household drain
• Maintains proper flow when correctly routed and secured
• Common symptoms: water leaking at the rear/under the washer, slow or no drain, long-drain errors, visible cracks or kinks
• Visible wear, brittleness, or residue buildup on the hose indicates replacement is needed

• Unplug the washer and move it for rear access; place towels or a pan to catch residual water
• Loosen clamps/fasteners and disconnect the old hose from the pump and drain connection; note the original routing
• Install the new hose in the same orientation; avoid kinks and secure all connections firmly
• Position the outlet per your model's instructions to prevent siphoning; run a test drain and check for leaks

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This drain pump assembly moves water out of the appliance during the drain portion of the cycle. Replacing a weak or failed pump restores proper draining and helps prevent standing water, odors, or repeated drain attempts.

• Actively pumps wastewater through the drain hose to household plumbing
• Engages during the drain step to clear the tub/sump between and after cycles
• Typical failure symptoms: won't drain or drains slowly; water left in the bottom; loud humming/grinding during drain; leaks around the pump area
• May fail due to worn motor, damaged impeller, or debris lodged inside the pump

• Disconnect power and turn off water supply; bail or wet-vac any standing water before starting
• Keep towels or a shallow pan ready; clamp or plug hoses to control residual water
• Transfer hose connections and any mounting hardware from the original pump; ensure seals and clamps are seated firmly
• After installation, run a short cycle to check for leaks

This factory fastener secures appliance components so panels, brackets, and trim stay tight and aligned. Replace a missing or stripped screw to stop rattles, restore a secure fit, and keep parts mounted as designed.

• Fastens panels, brackets, covers, and trim to the chassis
• Restores proper alignment and reduces vibration or rattling
• Replaces missing, rusted, or stripped hardware
• Helps maintain a solid, factory-style fit after service

• Disconnect power (and water, if applicable) before servicing
• Match the original screw location and orientation; start threads by hand to avoid cross-threading
• Use the correct driver for the head type; tighten snugly without overtightening
• Reuse any original washers or clips if present

This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.

• Mounts to the drive hub to rotate and circulate laundry during the wash cycle
• Helps create water currents and friction to loosen soils
• Worn or stripped splines can cause slipping and poor agitation
• Common symptoms: clothes not moving, poor cleaning results, unusual clicking/grinding from the tub base, visible cracks or wobble

• Disconnect power and shut off water before servicing
• Remove the center cap/cover, then remove the retaining bolt and lift off the old washplate
• Clean and inspect the hub splines; seat the new plate fully and reinstall the bolt—do not overtighten
• Run a short test cycle to ensure proper wash action

This electronic control board is the appliance's brain, coordinating inputs and outputs to run functions and features. Replacing a failed board can restore normal operation when controls are unresponsive or the unit behaves erratically. What it does:

• Directs power to loads such as motors, valves, heaters, or fans based on programmed logic
• Interprets user inputs and sensor/switch feedback to manage timing and options
• Monitors system status and can store/communicate diagnostic error codes
• Common symptoms of a faulty board include: won't power/start, unresponsive controls, intermittent operation, cycles not completing, or unexpected error beeps/codes

• Includes 1 electronic control board

• Disconnect power at the breaker before servicing; verify power is off
• Use ESD precautions and handle the board by the edges only
• Note/photograph all wire connections; transfer any jumpers or settings from the original board if present
• Some models require configuration or service-mode setup after installation—follow the tech sheet/service instructions for your unit

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action