Yard Machine Hook Tromm Spark Arrestor Parts

The Drum Motor Assembly is an OEM part for LG dryers. It serves as the powerhouse that drives the drum, enabling it to tumble clothes during the drying cycle. This essential component ensures your dryer operates smoothly, providing the necessary torque for consistent and efficient drying performance.

Causes of failure might include wear and tear from prolonged use, overload from trying to dry heavy loads, electrical issues like short circuits, or physical damage to the motor components. 

Symptoms of a bad Drum Motor Assembly include:

• The dryer drum fails to turn, even though the dryer powers on.
• Unusual noises, such as humming or buzzing, indicating the motor is struggling.
• The dryer stops unexpectedly during cycles or won't start at all.
• Decreased drying efficiency or clothes taking longer to dry due to inconsistent drum speed.

This OEM LG part is also compatible with Sears/Kenmore.

The Dryer Drum Baffle is an OEM part for LG dryers. This baffle is attached to the inside of the dryer drum and is designed to help lift and tumble clothes during the drying cycle. 

Causes of a bad dryer drum baffle can include wear and tear from regular use, physical damage from heavy or sharp objects, or becoming loose due to vibration over time. 

Symptoms of a bad dryer drum baffle include:

• Thumping or banging noises during the drying cycle
• Clothes not tumbling properly, leading to uneven drying
• Loose or rattling baffle inside the drum
• Visible damage or breakage on the baffle

This OEM LG part is also compatible with some Kenmore models.

Includes sensor probe

This is the heating assembly for an electric dryer. It generates and directs heat inside the drum so clothes dry efficiently and consistently.

• Heats incoming air as it passes through the heater housing and into the drum
• A failed heater can cause no heat, long dry times, or cool/warm air
• Visible breaks in the heating coil or tripped safety cutouts are common failure signs
• May help if the dryer runs but never reaches target temperature

• Unplug dryer; turn off breaker before servicing
• Access is typically from the rear; note wire locations before removal
• Replace any damaged connectors; ensure all ducts and seals are reinstalled correctly
• After installation, run a test cycle to ensure proper heat and airflow

The Gas Burner Valve Assembly is an OEM replacement part for LG gas dryers. It is a component located beneath the gas burner that controls the flow of fuel to ignite and maintain the flame. The valve assembly receives ignition and temperature signals from the dryer's control system to precisely regulate gas levels throughout drying cycles. This gas dryer burner valve includes two solenoid coils.

Causes of a faulty gas valve may involve wear over extended operation, mineral buildup on valve seats, or mechanical issues restricting gas flow at desired levels.

Symptoms of a bad gas burner valve assembly consist of:

• Erratic or inconsistent burner ignition between cycles
• Inability to achieve high heat settings when needed
• Burners not maintaining steady flame patterns
• Potential gas leaks detected around valves or tubing

This OEM LG part is also compatible with some Sears/Kenmore dryers.

This washer tub assembly is the stationary outer tub that surrounds the spin basket and contains the wash water. Replacing a cracked or damaged tub helps stop leaks and restores proper clearance for smooth, quiet washing and spinning.

• Creates a watertight chamber around the basket to hold wash and rinse water
• Maintains proper basket clearance; damage can cause rubbing or scraping sounds
• Provides connection points for hoses and water-level components
• Common signs it may be needed: leaks from the tub area, visible cracks or warping, persistent out-of-balance/spin errors, or internal scraping/grinding noises

• Disconnect power and water; shut off supplies and safely drain remaining water
• This is a major repair—allow time and consider a second person to help lift/support the tub
• Transfer model-specific parts from the original tub to the new tub as needed; reinstall all clamps, bolts, and sensors securely
• After reassembly, level the washer, and run a test cycle to check for leaks

This lamp assembly restores the interior drum light in your washer, improving visibility when loading and unloading. Replace a failed or damaged light to clearly see items and check the tub at a glance.

• Illuminates the washer drum when the door/light function is active
• Replaces a burned-out, flickering, or physically damaged lamp assembly
• Connects to the existing wiring harness and mounts in the factory location
• Symptoms include: drum light not turning on, intermittent flicker, or a cracked lens/housing

• Unplug the appliance before servicing; turn off water supply if opening the cabinet
• Access varies by model; may require removing the top/front panel and door boot clamp
• Disconnect the wiring connector carefully, seat the new assembly fully, secure it, and verify light operation before reassembly

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This lifter assembly is the drum baffle inside the washer's inner tub. It lifts and tumbles laundry as the basket turns—replacing a cracked or missing lifter restores proper turnover, helps prevent fabric damage, and quiets thumping noises.

• Provides the lift/turn action that moves clothes through water and detergent
• Helps distribute loads to reduce tangling and improve cleaning results
• A loose, broken, or missing baffle can cause rattling or scraping noises
• Damage can lead to poor turnover or fabric snagging

• Disconnect power before servicing; wear gloves—the inner drum edges can be sharp
• Access from the drum opening; remove the old lifter by releasing tabs or removing screws (varies by model)
• Align the new lifter with the inner-tub slots, lock tabs in place, and secure as designed
• Verify all baffles are firmly attached before running a test cycle

This cover cap is a small plug that snaps into an open hole on the washer's cabinet or panel. Replace a missing or damaged cap to restore a finished appearance and help keep dust, lint, and splashes out of the enclosure.

• Closes an unused hole on the appliance panel to maintain a sealed cabinet
• Helps keep debris and moisture from entering the machine
• Restores the clean, finished look of the unit
• Typical signs it's needed: missing cap, cracked or loose cap, or a visible open hole on the panel

• Disconnect power and water supply before servicing the appliance
• Align the cap with the hole and press straight in until fully seated
• No tools are typically required; avoid prying on painted surfaces
• Do not block any ventilation or drain openings—install only in the designated capped hole

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.

Outer door boot clamp secures the washer's door boot to the front panel and tub, restoring the watertight seal and helping prevent the boot from shifting or separating during wash cycles. What it does:

• Clamps the outer edge of the door boot to the front panel to hold the bellows firmly in place.
• Helps maintain a watertight seal at the door—install when you see water leaking from the front or along the door seam.
• Replaces bent, corroded, or loose clamps that allow the boot to pull away or develop gaps.
• Works with the boot to reduce movement and rubbing that can cause premature wear or leaks.

• Disconnect power and turn off water supply before beginning any repair.
• Access usually requires removing the washer door or front panel; drain the tub and remove the boot to fit the clamp correctly.
• Use appropriate pliers or a nut driver to secure the clamp; avoid excessive force that could damage the boot or mounting points.
• Inspect the door boot for tears or distortion; replace the boot if damaged to ensure a reliable seal.

This tub assembly is the main inner drum that holds clothes and spins during the wash and spin cycles, restoring a smooth, balanced wash performance when the original drum is damaged. Designed to replace a worn, cracked, or dented drum to help reduce noise and prevent fabric damage. What it does:

• Holds laundry during wash and spin cycles and provides the rotating surface for tumbling
• Replaces cracked, dented, or bent drums that cause scraping, rubbing, or visible damage to clothes
• Helps stop unusual noises or vibrations caused by a warped or damaged drum
• Restores proper drum alignment so the washer can drain and spin efficiently

• Disconnect power and water supply before beginning service
• Drain remaining water and remove front or top panel before accessing the drum
• Drum replacement typically requires removal of the wash plate, pulley, and possibly the tub seal—have basic hand tools and a service manual or diagram on hand

This metal mounting bracket secures internal components to the appliance frame, restoring proper alignment and reducing movement. Replace a worn or damaged bracket to stop rattling and maintain stable operation. What it does:

• Provides structural support to hold panels, controls, or assemblies in place
• Prevents excess vibration and noise caused by loose parts
• Keeps components aligned for reliable mechanical operation
• Helps maintain safe clearances between moving parts

• Turn off power and unplug the appliance before beginning work
• Use appropriate hand tools; retain any original fasteners unless replacements are specified
• Inspect adjacent parts and mounting points for damage; replace if worn

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently