Zfsb27dag-Ss Parts

A stamped mounting plate that secures the compressor to the refrigerator cabinet, helping keep the compressor stable and reducing vibration during operation. Fits original-equipment compressor assemblies. What it does:

• Provides a secure mounting surface to fasten the compressor to the cabinet frame
• Dampens and reduces compressor vibration that can cause noise or movement
• Keeps the compressor properly aligned for reliable refrigerant line routing
• Helps prevent stress on compressor mounts and surrounding components

• One compressor mounting plate

• Disconnect power to the appliance before starting any repair
• Support the compressor while removing and installing the plate to avoid strain on refrigerant lines
• Use the original mounting hardware when possible; replacement fasteners if needed

This replacement screw secures appliance components and panels where an 8-36 threaded fastener is required. Durable and ready for repair, it restores proper fit and reduces rattles or loose parts. What it does:

• Fastens panels, brackets, or components that use an 8-36 threaded screw
• Replaces stripped, lost, or damaged screws that cause vibration or loose parts
• Restores secure mechanical connections to help maintain normal operation

• One screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct driver and match thread engagement; do not force or cross-thread
• Tighten to snug; avoid overtightening which can strip threads or damage parts

A stainless-steel #6-20 screw (1/2" length) used to fasten appliance panels and components securely. Durable corrosion-resistant finish helps maintain a tight fit and long-lasting hold in wet or humid areas. What it does:

• Fastens trim, brackets, panels, and internal components where a #6-20 x 1/2" screw is specified
• Provides a corrosion-resistant connection for areas exposed to moisture
• Restores loose or missing fasteners that cause rattling or misalignment
• Matches OEM thread and length for proper fit and function

• One stainless steel #6-20 x 1/2" screw

• Turn power off and unplug appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; stop when the component is snug and aligned
• Replace any additional damaged fasteners with matching OEM screws

This dispenser crank links the dispenser solenoid and the ice chute door. When you press the dispenser lever, the crank pivots to open and close the ice door so cubes or crushed ice can dispense cleanly without warm air leaking into the freezer.

• Connects the solenoid to the ice chute door to control door movement
• Helps seal the chute when not dispensing to reduce frost and moisture issues
• Common failure signs include ice door not opening/closing, constant frost around chute, or warm/moist air leakage at dispenser
• Can cause ice clumping, frost buildup, or water/ice dispensed irregularly when worn or broken

• Disconnect power before servicing the dispenser area
• Access typically requires removing the dispenser front panel and trim; use care with plastic tabs and wiring
• Note linkage orientation to the solenoid and door flap before removal
• Inspect related parts for wear while open

Includes 12 washers.

This wiring harness is a factory-style wire assembly that routes power and signals between refrigerator components to restore electrical connections and proper function. It replaces damaged, frayed, or broken wire bundles to help eliminate intermittent operation or a loss of function. What it does:

• Provides the correct wires, connectors and routing to link controls, sensors, and motors
• Restores secure electrical connections when original wiring is cut, burned, or corroded
• Helps stop intermittent control issues, lights or components that work only sporadically
• Maintains OEM routing and connector fit for a reliable replacement

• One complete wiring harness assembly as pictured

• Disconnect power at the breaker or appliance plug before starting any repair
• Compare the new harness to the original to confirm connector types and lengths before installation
• Secure wiring with existing clips and retainers; avoid pinching or routing near hot components

This rear wheel roller replaces a worn or damaged drawer/glide wheel to restore smooth movement and reduce sticking or noise. Durable molded construction fits the rear guide position to help support and steady the sliding drawer or bin. What it does

• Supports and guides the appliance drawer or bin for smooth in-and-out motion
• Replaces cracked, chipped, or worn rear wheel that causes binding or catching
• Helps reduce squeaks and uneven movement from a damaged roller
• Restores proper alignment and load support at the rear glide point

• One rear wheel (roller)

• Disconnect power and remove the drawer/bin per your owner's manual before replacing the wheel
• Typically installs by snapping or sliding into the rear glide bracket; basic hand tools may be needed
• Inspect mating tracks or brackets for damage and clean debris before installing the new wheel

Package of 12

8 - 18 x .375

This is a 10-24 x 1.0 inch screw used to secure appliance panels and components. It replaces worn or missing fasteners to restore proper fit and reduce rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable
• Stops vibrating or rattling caused by loose or missing screws
• Restores proper grounding/attachment where a threaded fastener is required
• Matches OEM thread size and length for a correct fit when replacing damaged screws

• Use the correct driver bit and turn carefully to avoid stripping the head or threads
• Do not overtighten; snug until secure to prevent damage to mating parts
• Replace like-for-like with the same thread size and length for proper fit
• Disconnect power and follow appliance safety guidelines before accessing internal components

This stationary display blade secures and positions the appliance's front display/overlay so controls and indicators stay aligned and visible. It replaces a cracked, loose, or missing display blade to restore a stable display surface. What it does:

• Holds the display/overlay in the correct position behind the control panel
• Prevents the display from rattling or shifting during normal use
• Restores a flush, aligned appearance when the original blade is broken or worn
• Helps keep buttons and indicators properly supported for reliable operation

• Disconnect power to the appliance before starting any repair.
• Removal usually requires removing the front/display trim or bezel; use basic hand tools.
• Handle small plastic parts carefully to avoid cracking during removal/installation.

Includes 12 screws.