Zgu85nsmss Parts

This hot-surface igniter and harness assembly replaces the oven's failed ignition module so the burner can light reliably. It restores normal oven heating for baking and broiling when the igniter is the cause of no-heat issues. What it does:

• Provides the hot surface that glows and opens the gas valve to light the oven burner
• Replaces a cracked, broken, or weak igniter that won't heat or take too long to glow
• Restores consistent ignition when intermittent lighting, delayed heat, or no-heat symptoms occur
• Includes the pre-attached wiring harness for a direct electrical connection to the oven controls

• Disconnect power and gas supply before starting any repair; work only when the appliance is fully powered off
• Handle the ceramic igniter element carefully—it is fragile and can crack if dropped or flexed
• Verify correct connector orientation and secure mounting to avoid loose electrical or gas connections

This ignition module mounting bracket secures and positions the stove/oven spark ignition module for reliable spark alignment. Replacing a damaged or bent bracket restores proper module placement to help resumes normal ignition. What it does:

• Secures the ignition/spark module to the appliance chassis so the electrode aligns with the burner.
• Keeps the module stable to prevent intermittent or no-spark conditions caused by a loose or misaligned module.
• Helps maintain correct wire routing and strain relief to reduce connector or wiring stress.
• Can prevent rubbing or contact that may cause intermittent clicking or failure to ignite.

• One ignition module mounting bracket.

• Disconnect electrical power and shut off gas supply before beginning service.
• Handle the ignition module and electrode carefully to avoid damage; support the module while removing/installing the bracket.
• Retain and reuse original screws or fasteners unless replacements are specified by the manufacturer.

This handle grommet cushions and secures a range or oven door handle, preventing vibration and wear while keeping the handle snug. It's a small replaceable part that restores proper fit and reduces rattling. What it does

• Provides a soft mounting surface between the handle and door to prevent metal-to-metal contact
• Keeps the handle tight and aligned to stop looseness or movement
• Dampens vibration and reduces rattling during operation
• Helps protect the door finish where the handle mounts

• One handle grommet

• High-level push-fit part; remove the handle or access the mounting area per your model's service instructions
• Disconnect power to the appliance before beginning service when accessing electrical or heated components
• Use a plastic trim tool or small screwdriver to pry out the old grommet carefully to avoid scratching the door
• If the handle or mounting hardware is damaged, inspect and replace as needed for a lasting repair

Natural gas. SM 1.07mm

This 10-24 x 3/16" screw is a replacement fastener used to secure panels, brackets, or components in compatible appliances. It restores proper fit and helps prevent vibration or parts coming loose during operation. What it does:

• Secures trim, panels, or internal brackets where a 10-24 thread and short 3/16" length are required
• Replaces missing or stripped screws that cause rattling or loose components
• Restores proper alignment of parts held by this fastener
• Works wherever OEM specifies a 10-24 x 3/16" screw for reliable fastening

• One (1) 10-24 x 3/16" screw

• Use the correct screwdriver or driver bit sized for the screw head to avoid stripping
• Tighten until snug; avoid over-torquing which can strip threads or damage components
• Disconnect power and follow appliance safety precautions before accessing internal parts
• If fastening into plastic, avoid excessive force

A small adhesive MG logo emblem that restores the original appearance of your appliance. This peel-and-stick badge replaces a worn, faded or missing logo to keep the exterior looking factory-fresh. What it does:

• Cosmetic replacement for a missing, scratched or faded MG emblem
• Adheres to control panels, doors or trim where the original badge was located
• Restores brand identification and a finished appearance to the appliance
• Simple adhesive design avoids the need for fasteners or tools

• Clean and dry the mounting surface before applying to ensure good adhesion
• Peel backing and press firmly in place, aligning carefully before contact
• Avoid repositioning once attached; removal may damage the emblem or finish
• For safety, disconnect power before working near electrical controls or panels

This stainless steel control knob replaces a worn or damaged range/oven control knob and restores positive, easy-to-read control of surface burners and oven functions. Durable finish keeps your appliance looking factory-fresh. What it does:

• Replaces a damaged, cracked, loose or missing control knob to restore safe, accurate control of burners and oven settings
• Installs on standard splined control shafts to select heat levels and oven functions
• Provides a stainless-steel finish that resists everyday wear and improves appearance
• Matches multi-ring styling used on select GE ranges and cooktops for a uniform look

• One stainless steel control knob (multi-ring)

• Turn all controls off and disconnect power to the appliance before servicing
• Pull the old knob straight off the control shaft; align splines and push new knob on until seated
• If knob is stiff, check for debris on the shaft; do not force or hammer the part