Zics360nrdhl Parts

Nut for 1/4 inch tubing.

This drawer slide assembly supports and guides your refrigerator's drawer so it opens and closes smoothly. Replace a cracked or worn slide to restore proper alignment and stop sticking, dragging, or dropped drawers.

• Supports the drawer and provides smooth sliding action
• Maintains alignment to prevent binding or popping off the track
• Replaces cracked, warped, or seized slide components
• Typical symptoms: drawer hard to open/close, crooked, or falls off

• Disconnect power before servicing
• Empty and remove the affected drawer and any obstructing shelves for access
• Remove fasteners securing the old slide; transfer any reusable brackets/clips from the original if applicable
• Align and secure the new slide, then verify the drawer engages both tracks and glides freely

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This defrost heater warms the evaporator coils during the automatic defrost cycle to melt frost and keep air moving. When it fails, ice builds up, airflow drops, and temperatures rise in the fresh food compartment.

• Heats the evaporator to clear frost/ice so the fan can circulate air
• Helps maintain stable temperatures and normal airflow between freezer and refrigerator sections
• Common signs of failure: heavy frost on the back freezer panel, warm refrigerator/cool freezer, fan noise from ice contact, long run times
• Works with the defrost thermostat and control to complete defrost cycles

• Unplug the refrigerator before service; use caution around sharp evaporator fins
• Access the evaporator behind the freezer's rear panel and fully defrost ice before replacement
• Route wiring exactly as original; avoid kinking or stressing the heating element
• After reassembly, restore power and verify a successful defrost cycle per service procedures

Upper freezer slide liner replaces the plastic guide that supports and guides the upper freezer shelf, restoring proper shelf alignment and smooth sliding for easier access and safer storage. What it does:

• Guides and supports the upper freezer shelf along its track to prevent tipping or misalignment
• Keeps the shelf sliding smoothly so drawers and items move without catching
• Helps prevent shelf damage from uneven loading or cracked supports
• Replace when the liner is cracked, worn, or the shelf slides unevenly or binds

• Remove food and the affected shelf before replacing the liner for safe, clear access
• In many cases no tools are required—slide out the old liner from the track and snap the new liner into place
• Inspect mating track and adjacent clips for damage; replace damaged components to ensure proper fit

This condenser fan mounting bracket secures the condenser fan motor and blade in the correct position to move air across the coils. Replacing a cracked or bent bracket restores stable mounting, reduces vibration, and helps maintain proper condenser airflow.

• Holds the condenser fan motor/blade assembly in alignment for proper airflow through the condenser
• Maintains clearance to prevent the fan blade from rubbing or contacting nearby components
• Helps reduce rattling, vibration, or scraping noises from the rear of the refrigerator
• Damage or misalignment can contribute to restricted condenser airflow and warmer temperatures

• Disconnect power and pull the refrigerator away from the wall to access the rear service area
• Remove the rear lower access panel; note wiring and hardware locations
• Support the fan motor/blade while removing the old bracket; transfer motor, blade, grommets, and screws to the new bracket
• The fan spins freely with proper clearance and correct airflow direction before reassembly

This freezer drawer slide is installed on refrigerators with bottom drawer freezers. The slide makes it possible to open the drawer without any jamming.If there is noticeable difficulty opening the slide-out freezer, or it is unable to be opened at all, the problem is likely with the slide rail. Inspect the length of the slide rail and if there are any broken pieces or missing screws, this is the culprit. If the damage is unable to be fixed by replacing a few screws, a replacement will need to be ordered. Begin the installation by removing the old pieces of slide rail. Prepare the screws for the new installation. Fasten the new slide rail to the refrigerator by inserting the screws in their proper mounting. To reinsert the freezer drawer, tip at an angle and insert into the slide rail.This freezer drawer slide rail is a genuine OEM replacement part and is sourced directly from GE. The product listed is only available individually and is not included with any other parts or the original appliance. This part Is compatible with GE appliances.

Also called a thermodisc, this evaporator-mounted defrost thermostat monitors coil temperature and switches the heater off when frost is cleared. Replacing a failed thermostat helps restore proper defrosting, airflow, and consistent refrigerator temperatures.

• Senses evaporator coil temperature during the defrost cycle
• Closes when the coil is cold to let the defrost heater energize; opens as the coil warms to stop heating
• Helps prevent heavy frost buildup that restricts airflow and cooling
• Symptoms include ice on the rear freezer panel, poor cooling, or the defrost heater not turning on

• Disconnect power before servicing
• Access from the freezer by removing shelves and the rear panel
• Attach the thermostat securely to the same tubing location for good thermal contact; route wires away from moving parts
• Fully defrost any existing ice before returning the unit to service

This slide rail assembly mounts beneath the fresh-food shelf to guide and support the deli/snack drawer, helping it open and close smoothly. Replace a cracked or worn slide to stop sticking, tilting, or the drawer dropping off its track.

• Supports and aligns the deli/snack drawer under the fresh-food shelf
• Provides smooth sliding action along the track
• Helps keep the drawer level and properly seated
• Common symptoms: drawer sticks, sags, falls off, or the rail is visibly cracked/broken

• Disconnect power; remove the drawer and clear the shelf area
• Remove screws or clips securing the old slide; note its orientation
• Install the new slide and transfer any reusable hardware if needed
• Reinstall the shelf and drawer; verify smooth travel before loading

A left-hand top door closure assembly that secures and cushions the refrigerator door at the upper hinge for smoother closing, improved alignment, and a tighter seal. Restores proper door movement and reduces rattling or sag. What it does

• Guides and cushions the top of the door at the hinge so the door closes smoothly and stays aligned.
• Helps maintain an effective seal to reduce air leaks and temperature fluctuations.
• Reduces door wobble, sagging, or rattling caused by worn or broken closure components.
• Works with the top hinge area; symptom linkage is safe and commonly accepted (door failing to close fully, door misalignment, or excessive movement).

• Disconnect power to the appliance and remove food/items from the door area before starting.
• Support the door while removing or installing hinge/closure hardware to prevent dropping or damage.
• Uses basic hand tools; follow OEM service instructions or model-specific diagrams for correct hinge orientation and torque.

Flexible front door seal (gasket) that restores a tight closure between the appliance door and cabinet to help maintain interior temperature and reduce moisture, frost and energy loss. Use when the existing seal is cracked, torn or no longer seals fully. What it does:

• Creates an airtight seal around the door to keep cold air in and warm, moist air out.
• Helps reduce frost build-up, water or ice between compartments, and visible condensation.
• Supports consistent internal temperatures to protect food and improve efficiency.
• Common symptom: visible gaps, a torn or deformed gasket, or cold loss around the door edge.

• Disconnect power or unplug the appliance before service.
• Remove food and any removable door shelves or bins that obstruct access.
• Clean and dry the door sealing surface before fitting the new gasket for best contact.
• Fit the gasket starting at a corner and work around the door; gently warm stiff seals to make them more pliable if needed.

This ice bucket is the removable plastic bin that collects and stores ice from the ice maker, keeping cubes contained and easy to access. It restores proper ice storage and makes removing or pouring ice simple. What it does:

• Holds and stores ice produced by the freezer ice maker so cubes stay contained and sanitary.
• Guides ice from the ice maker into the storage bin to prevent spills and jams.
• Allows easy removal for scooping, pouring, or cleaning when ice build-up occurs.
• Commonly replaced when the bucket is cracked, warped, missing, or no longer seats properly.

• One ice bucket.

• Unplug or disconnect power to the appliance before servicing the ice maker area.
• Slide the bucket into the freezer compartment aligning tabs or guides; do not force.
• Handle plastic tabs and mounting points carefully to avoid breakage.
• Inspect the ice maker assembly and chute for ice buildup or damage.

This front vegetable pan glass seal replaces the worn or damaged gasket that fits along the glass front of a refrigerator crisper/vegetable drawer. Restores a snug fit to help reduce drafts, rattling and food falling beneath the drawer. What it does:

• Seals the front edge of the crisper/vegetable drawer glass to help maintain proper airflow and keep produce fresher.
• Holds the glass front securely to reduce rattling, slipping or gaps.
• Prevents small food items and debris from slipping under the pan.
• Common symptoms: torn, brittle or missing seal; visible gap at the drawer front; rattling or debris collecting beneath the drawer.

• Remove food and slide out the crisper/vegetable drawer to access the glass front before replacing the seal.
• Remove the old seal and clean the channel of any debris or adhesive; press the new seal firmly into the channel until fully seated.
• Wear gloves and use caution around glass edges to avoid cuts; no special tools are usually required.
• If clips or adhesive are present, inspect and reuse or replace them as needed; replace cracked or damaged glass rather than relying on the seal.

Freezer basket slide for the upper basket. This rail supports and guides the top freezer basket so it glides in and out smoothly. Replace a cracked or warped slide to restore proper movement and alignment.

• Supports and tracks the upper freezer basket along the cabinet wall
• Provides smooth sliding action for easier access to frozen items
• Replace when the slide is cracked, broken, or deformed
• Typical symptoms: basket binds or tilts, scrapes, pops out, or won't close fully

• Disconnect power to the refrigerator before servicing
• Remove the upper basket; release locking tabs or screws and lift out the damaged slide
• Position and secure the new slide as shown in your model's diagram; do not overtighten screws
• Reinstall the basket and verify smooth travel and proper door sealing

This fill tube kit routes water from the refrigerator's inlet to the ice maker, restoring reliable water delivery for ice production and reducing drips from a cracked or damaged tube. Simple replacement for worn or broken factory tubing. What it does:

• Replaces the water fill tube that supplies water to the ice maker assembly.
• Restores proper water flow so the ice maker can fill and form ice.
• Stops leaks or drips caused by split, brittle, or disconnected tubing.
• Helps resolve symptoms like no/low ice production or visible water pooling under the freezer/ice maker area.

• Disconnect power and shut off the water supply before starting work.
• Handle grommets and fittings gently to avoid damage; inspect seals and replace if worn.
• Confirm correct routing and secure mounting to prevent kinks or rubbing.