Ziss480dmss Parts

A 6 x 1/2 inch pan-head Phillips screw used to fasten panels, trim, brackets and small assemblies on appliances. Replacing worn or missing screws restores secure mounting and reduces vibration or rattling. What it does:

• Fastens panels, brackets and trim where a 6 x 1/2 in. pan-head Phillips screw is required.
• Stops loose or rattling parts caused by missing, stripped or corroded screws.
• Provides the correct head profile for a Phillips driver to allow proper torque and seating.
• Used in non-structural fastening points on appliances.

• Always disconnect power and unplug the appliance before beginning repairs.
• Use the correct-size Phillips screwdriver to avoid cam-out and head damage.
• Do not over-tighten; over-torquing can strip threads or deform mating parts.
• Inspect mating threads and replace damaged components before installation.

This is a bottom door hinge screw that secures the lower hinge assembly to the appliance door, restoring proper alignment and stable door movement. Use it to replace stripped, missing, or damaged hinge hardware. What it does

• Secures the bottom hinge to the door and helps keep the door aligned and level.
• Restores smooth, consistent opening and closing when a worn or missing screw causes sagging or misalignment.
• Prevents further wear to hinge components by maintaining correct hinge positioning.
• Works with original hinge assemblies; use the correct screw to avoid loose or unstable doors.

• Disconnect power to the appliance before performing any door or hinge repairs.
• Support the door while removing/installing the hinge screw to prevent the door from falling or causing injury.
• Use the correct screwdriver or bit to avoid stripping the screw head.
• Replace any additional worn hinge hardware as needed for proper alignment.

This left hand base channel is the lower cabinet support piece that helps secure and align the appliance's front base. It restores proper fit and stability at the cabinet bottom after damage or wear. What it does

• Provides structural support for the appliance's lower front cabinet, keeping panels aligned.
• Replaces a bent, cracked or missing base channel that causes gaps or misalignment.
• Helps prevent rubbing or binding between the cabinet and kickplate or floor.
• Restores correct mounting points for adjacent trim and hardware.

• Intended for the left/front lower cabinet area; verify orientation before installing.
• Basic hand tools required; support the appliance while removing and installing to avoid strain.
• Disconnect power and water (if applicable) and follow all safety precautions before beginning work.
• If mounting hardware is damaged or missing, replace fasteners with OEM-equivalent parts.

This right-hand base channel restores the lower support and alignment for a refrigerator door, helping the door sit level and operate smoothly. It replaces a bent, cracked or missing channel to improve door fit and stability. What it does:

• Provides the structural lower support the door mounts to, keeping the door aligned and stable
• Corrects door sag, uneven gaps, rubbing or difficulty closing when the channel is damaged
• Reinforces the hinge and threshold area to maintain proper door seal and operation
• Matches the OEM mounting points for a direct-fit replacement when installed correctly

• Turn off power to the appliance and remove any refrigerated contents from the door before beginning
• Installation typically requires basic hand tools; remove door and lower trim as needed for access
• Handle carefully to avoid scratching the finish and align mounting holes before securing hardware
• If hinge pins, seals or fasteners are worn or missing, replace them per manufacturer recommendations for best results

This diffuser case assembly directs cooled air from the evaporator into the refrigerator compartment to help maintain even temperature and airflow. It replaces a cracked, broken or missing diffuser housing to restore proper air distribution. What it does:

• Channels chilled air into the fresh-food compartment for more consistent cooling
• Protects internal ducting and supports the diffuser flap/door
• Helps reduce local hot spots or inconsistent temperatures caused by damaged housing
• Fits into the factory mounting location and works with the existing duct components

• Disconnect power to the appliance before starting any repair
• Accessible from inside the fresh-food compartment; remove shelves/controls as needed for access
• Align tabs and press into place until clips fully engage; do not force or bend plastic parts
• If other diffuser components (flap, seals) are damaged, inspect and replace as needed for full function

This replacement water filter housing secures the refrigerator water filter cartridge and channels water to the dispenser and ice maker for reliable flow and reduced leaks. Restores a solid connection between the filter and water lines. What it does:

• Holds and seals the water filter cartridge in place
• Directs filtered water to the dispenser and ice maker
• Helps stop leaks or drips at the filter location
• Can improve weak or intermittent water flow caused by a damaged housing

• Turn off the refrigerator water supply before replacing; dispense remaining water to relieve pressure
• Disconnect power if needed for access and to avoid electrical contact
• Inspect O-rings and replace if damaged; lubricate with food-grade silicone if recommended
• Hand-tighten connections and check for leaks after restoring water; do not overtighten plastic fittings

This left-hand slide can rack replaces the fridge can organizer that holds and guides canned goods for easy access. It restores smooth sliding and organized storage on the refrigerator door or shelf area. What it does:

• Supports and holds canned beverages/containers securely on the left side of the slide assembly
• Guides cans forward for easy one-hand access and organized storage
• Replaces broken, cracked, or warped left-side can rack that causes cans to fall or not slide
• Improves usability when the original rack is loose or doesn't align with the slide mechanism

• One left-hand slide can rack

• Remove all contents from the rack area before installing
• Install by aligning with existing slide rails and snapping or fastening into place without forcing
• If fasteners or clips are damaged, replace them before use; keep original hardware if reusable
• For safety, unplug the appliance or turn off power to model-specific features before service

This refrigerator door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace a torn, warped, or leaky gasket to restore proper sealing and consistent temperatures around the door opening. What it does:

• Seals the door perimeter against the cabinet to limit air leaks
• Helps maintain interior temperature and reduce condensation or frost near the door
• Supports proper door closing and alignment
• Common symptoms of a failed gasket: visible cracks/tears, door not sealing, condensation or frost at the door edge, warm spots near the door

• One door gasket

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use low heat) to make it pliable
• Remove the old gasket and clean the retainer/channel thoroughly
• Press the new gasket fully into the retainer; square corners, check for even contact all around, and use gentle low heat to relax waves; allow up to 24 hours for the gasket to conform

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation