Solenoid Parts

This single-solenoid water inlet valve controls the flow of water from your home supply into the refrigerator's water system, typically feeding the ice maker. A failing valve can stop fill, cause slow or inconsistent fills, or allow unwanted seepage.

• Opens and closes when energized to regulate water to the appliance's water circuit
• Common symptoms: no ice production, small or hollow cubes, water seeping into the ice maker, or leaks at the valve
• Electrical failure (open coil) or mineral debris can keep the valve from opening or closing properly
• Restores proper water fill and reliable shutoff when replaced

• Unplug the refrigerator and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch residual water
• Label or photograph tubing and wires for correct reassembly; cut plastic tubing square and fully seat it
• Restore water and power, then check all connections for leaks

Comes with two filters.

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This drain valve controls the flow of water out of the appliance to remove standing water and prevent overflow. Replacing a faulty valve restores normal draining and helps stop pooling or persistent drain error symptoms. What it does:

• Opens and closes to release water from the appliance drain path.
• Works with the pump/drain line to move water out during cycles.
• Common issues indicating failure: appliance won't drain, water pooling, or intermittent drain errors.
• Fits as the direct replacement component for the OEM valve in affected models.

• Disconnect power and turn off the water supply before starting work.
• Expect residual water in hoses; have towels and a pan ready to catch spills.
• Remove and replace using basic hand tools; keep clamps and seals secure to avoid leaks.

This water inlet valve assembly controls and regulates the flow of water into your washer during fill. A working valve helps the washer start and complete cycles reliably without leaks, overfilling, or long fill times.

• Opens and closes to allow household water to enter when the control calls for a wash or rinse
• Shuts off water flow when not energized to prevent unwanted filling
• Helps maintain proper water levels and flow for consistent performance
• Common symptoms: no fill or slow fill, continuous filling or overflow, leaks at the valve or hose connections, or buzzing with little/no water flow

• Unplug the appliance and shut off water supplies before servicing
• Place towels or a pan to catch residual water and relieve line pressure
• Label or photograph connectors/hoses; transfer them one at a time to the new valve
• Tighten hose fittings snugly and run a test fill to check for leaks

Dual water inlet valve that controls water supply to the refrigerator dispenser and icemaker, restoring proper water and ice delivery and helping stop leaks or erratic flow caused by a failed valve. What it does:

• Routes and controls water flow to the dispenser and icemaker; a defective valve can cause no water dispensing or no ice production.
• Uses two independent solenoids to send water where needed; failure or blockage can cause weak, intermittent, or continuous flow.
• Seals and meters incoming water from the supply line; worn valve seals can lead to leaks or flooding.
• Replaces the factory inlet valve assembly to restore normal water operation when the original valve fails.

• Shut off refrigerator power and the household water supply before starting the repair.
• Relieve water line pressure and disconnect lines carefully to avoid spills; keep a towel and bucket handy.
• Ensure electrical connectors are fully seated and water fittings are snug—do not overtighten plastic fittings.
• After installation, restore water and power, then check all connections for leaks and proper dispenser/icemaker operation.

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This guide assembly is the track that supports and directs a dishwasher rack as it slides in and out. Replace a worn or damaged guide to restore smooth rack movement, alignment, and reliable loading. What it does:

• Provides the sliding path that supports and guides the dishrack
• Maintains rack alignment to prevent derailment
• Helps the rack extend and retract smoothly without binding
• Common symptoms: rack hard to slide, tilts or falls off track, scraping/grinding noises, visible cracks or broken tabs on the guide

• 1 guide assembly

• Disconnect power and shut off water before servicing the dishwasher
• Pull the rack out and remove any end caps or stops to access the guide
• Release locking tabs or screws, note orientation, and swap the old guide with the new one
• Reinstall stops/end caps and test rack travel for smooth operation

The Latch is an OEM replacement part for Frigidaire built-in microwaves. Securely mounted to the top interior section of the microwave cavity door, the positive-locking latch holds the door safely shut during operation. Crafted from corrosion-resistant materials for extended use, the latch handle withdraws the hook mechanism with a simple pull to conveniently access food within.

Symptoms of a bad latch include:

• The microwave door popping or falling open unexpectedly  
• Difficulty closing or fully engaging the secure latch hook 
• Wear signs like loose mounting points or a worn handle

Causes can involve repeated opening/closing cycles gradually loosening mounting fixtures, or parts rendered ineffective by moisture intrusion over time.

Replacing this Frigidaire OEM latch prevents potential microwave door opening during cooking cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore built-in models.

This LP gas conversion kit lets compatible gas ranges be converted from natural gas to LP (propane), supplying the correct orifices and settings so burners run safely and produce expected heat on LP fuel. What it does:

• Replaces factory burner orifices and related fittings to match LP fuel pressure and flow.
• Helps restore proper flame size and burner performance after switching from natural gas to propane.
• Addresses symptoms such as weak or yellow flames, uneven heating, or reduced burner output after fuel change.
• Intended for use only on ranges specified by the manufacturer for this conversion kit.

• Shut off the gas supply and disconnect power before beginning work.
• After installation, perform a leak test and verify correct flame characteristics on all burners.
• Keep original parts and the instructions for future reference and warranty requirements.

The Latch Ovn is an OEM part for GE ranges. It functions as the latch mechanism that secures the oven door in the closed position during cooking.

The latch oven is responsible for safely and securely holding the oven door shut while in use. It allows for controlled opening and closing of the door to facilitate easy access inside the oven cavity.

Causes of a bad latch oven can include wear and tear over time, failure of mechanical components within the latch mechanism, or damage from overtightening or forced opening/closing of the oven door.

Symptoms of a bad latch oven include:

• The oven door not latching fully or securely in the closed position
• Difficulty opening or closing the oven door
• The door popping or springing open unexpectedly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven door latch assembly secures the door and communicates lock status to the control. Replacing a worn or jammed latch restores safe door locking so bake and self-clean cycles can start and finish correctly.

• Locks and unlocks the oven door when engaged or commanded by the control
• Secures the door during the self-clean cycle for safety
• Helps resolve issues such as a door that won't lock or unlock, self-clean that won't start/finish, or a persistent "door locked" indicator
• Wear, binding, or internal failure can prevent proper latching

• Disconnect power at the breaker before servicing
• Access location varies by model; typically serviced from the top, rear, or control/console area—follow your model's service procedures
• Transfer any mounting hardware and reconnect wire harnesses one at a time
• After installation, verify smooth latch movement and door locking before running a cycle

This replacement water inlet valve controls the flow of water to the appliance's dispenser and ice-making components, restoring normal fill and preventing supply interruptions when a valve fails. What it does

• Opens and closes to allow water into the dispenser and ice maker on demand
• Restores water flow if the dispenser or ice maker won't fill
• Stops water supply when closed to help prevent overfilling or continuous flow
• Common replacement for intermittent flow, no-water, or leaking symptoms

• Turn off power and shut off the water supply before starting any work
• Inspect fittings, hoses, and seals and replace any damaged components to prevent leaks
• Use basic hand tools; hand-tighten fittings and check for leaks after reconnecting water