Ecb Parts

A replacement electronic clock timer for electric ranges and ovens that restores timekeeping and timed cooking functions. Replaces a worn or unresponsive control so your oven can display the clock and run timed bake, broil, or self-clean cycles. What it does:

• Displays the current time and lets you set the kitchen timer and timed cooking functions
• Enables delayed start, auto shut-off, and timed bake/clean features controlled through the oven control
• Replaces a blank, flickering, or non-responsive clock/timer display
• Works as the interface for oven timing functions but does not include touchpad overlays or control panel trim

• Disconnect power to the appliance before beginning work to avoid shock or damage
• Remove the oven control/console trim to access and replace the clock timer; basic hand tools are typically required
• Handle the control gently; avoid touching circuit board components and connectors

This power control board assembly replaces the sub power PCB that manages voltage and signal distribution to the appliance's main controls. Restores control reliability and resolves power-related control issues when the board is at fault. What it does:

• Routes power and control signals between the main control and subsystem components
• Helps the appliance respond correctly to control inputs and cycles
• Commonly replaces a board that causes no power to portions of the appliance or erratic electronic behavior
• Addresses symptoms such as control panel unresponsiveness, intermittent operation, or error codes tied to power/control faults

• Disconnect power before attempting any repair to avoid shock or damage
• Handle the PCB by its edges and avoid static discharge; use proper ESD precautions
• Installation requires basic hand tools and involves removing panels and connectors; keep track of fasteners and wiring
• Replace only with the exact part number to ensure proper fit and function

This part is an control board for washers. The control board is the part that controls the main functions of a washing machine. It is the main component that sends signals to the washer to perform its intended functions, controlling the desired washer settings. If the washing machine is not filling with water, spinning normally, or draining properly, this might mean it's time for a new control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the washer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board and be sure to take note of which wires go where by taking a photo with a phone camera. Then disconnect the air hose. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the air hose to the back of the control panel, and reconnect the wires into the back of the new control board. This genuine control board is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brand washers.

The Electronic Control is an OEM replacement part for Whirlpool gas ranges. It controls various functions such as temperature regulation, timer settings, and cooking modes.

A bad oven control board can occur due to electrical malfunctions, power surges, or general wear and tear. If you notice symptoms such as the oven not reaching the desired temperature, erratic temperature fluctuations, or unresponsive controls, it may be time to replace the control board.

Symptoms of a bad oven control board include:

• Oven not reaching desired temperature
• Erratic temperature fluctuations
• Unresponsive controls

Restore the functionality and precision of your Whirlpool gas range by replacing the faulty or worn-out oven control board with this genuine OEM part.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Made for use on electric ranges, this part is an oven relay control board. The purpose of this part is to receive signals from the main oven control board. This component then operates relays to regulate the oven elements. Unplug the appliance from the electrical outlet and allow it plenty of time to cool off before attempting to perform repairs. The replacement process is fairly easy and takes about 20 minutes to complete.If the oven won't maintain the temperature, it is possible that the oven relay control board is faulty. In many cases, the oven will heat up initially but won't kick in to heat the oven throughout the baking process. The oven relay control board can be tested using a VOM to check for continuity. This oven relay control board is sold individually. It is sourced straight from the manufacturer. This particular part is compatible with ovens that are manufactured by General Electric.

The module control assembly is the appliance's electronic control board that manages cycles, timers and control functions. Replacing a failing board can restore responsive controls and correct cycle operation. What it does:

• Directs cycle selection, timers and communication to components so the appliance runs the selected programs.
• Manages signals between the user interface and internal parts; failures often cause unresponsive or intermittent controls.
• Common symptom linkage: unit won't start, cycles won't advance, erratic operation, or display/control errors.
• Interfaces with the control harness and panel to coordinate motors, valves and other driven components.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Handle the control board by its edges and avoid touching circuitry; use anti-static precautions if available.
• Verify harness connectors, fuses and wiring before replacing the board; confirm connector orientation and secure mounting.

This replacement dryer timer advances the cycle sequence and lets the dryer move through timed and automatic settings so clothes dry on the selected cycle. Restores selector/timer control when the original timer fails. What it does:

• Controls cycle advancement so the dryer progresses through timed and automatic cycles
• Enables selection of timed and automatic dry settings via the control knob
• Common symptom: dryer won't advance through cycles or stays stuck on a setting
• Needed if the timer knob doesn't respond, the timer won't turn, or cycles do not complete

• Always disconnect power to the dryer before starting any repair
• Access usually requires removing the control panel or console—handle trim and fasteners carefully
• Note wire locations or take a photo before disconnecting harnesses to ensure correct reassembly

This mechanical oven timer restores simple dial-based timing and end-of-cycle alerts so you can set cook times and receive audible reminders. It replaces a worn or non-advancing timer to bring back reliable basic timing functions. What it does:

• Advances and times cook/clean cycles so the oven rings when a set time ends
• Restores manual timing when the clock/timer no longer advances
• Replaces a timer that fails to sound the end-of-cycle buzzer
• Provides a direct, dial-based alternative to electronic controls on compatible units

• Always disconnect power to the appliance before beginning service
• Access typically requires removing the control panel or console; support the console while detaching the timer
• Align the timer shaft and knob carefully during installation to avoid damage

This inverter assembly is the control module that powers and regulates the refrigerator compressor, restoring variable-speed operation and helping maintain proper cooling. Install to replace a failed or damaged inverter module. What it does

• Converts and supplies the correct power signals to the compressor so it can run at variable speeds
• Can eliminate error codes or fault indicators related to the inverter/control module
• May reduce abnormal compressor noise or intermittent compressor operation when the inverter is faulty

• One inverter assembly

• Disconnect power at the breaker before starting work
• Handle the board and connectors with care; avoid static discharge and damaged wiring
• Verify connector orientation and secure all plugs before reapplying power

This Drive PWB is the replacement electronic board that controls the appliance's drive functions, restoring reliable motor and transmission commands for normal operation. What it does

• Controls drive motor speed and direction and sends/receives signals to the main control
• Can resolve symptoms such as no spin/agitate, erratic drive behavior, or unresponsive drive controls
• Re-establishes communication between drive assembly and console when board failure is the cause
• Works as the direct replacement board for the drive electronics in compatible units

• Disconnect power to the appliance before service to avoid shock—verify unit is de-energized
• Handle the board by its edges and avoid touching components; observe basic ESD precautions
• Reconnect all connectors in their original positions and secure mounting hardware

This is a genuine OEM replacement timer for a top load washing machine. This replacement part is compatible with many different top load washing machines.The timer is a vital part to the washing machine as it controls the internal electrical components and the duration of the cycles. If this part is broken or becomes faulty in any way, the user will notice the machine does not cycle properly. Cycles may not begin, or the washer may continue running for too long. This can cause additional damage or wear and tear on the washing machine. Wear work gloves, drain the washer if there is still water in it, and unplug the appliance from power before beginning repairs.This authentic part can be used with other models and brands such as Whirlpool, Maytag, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Norge and others. It is sold individually and is made of high quality, non-corrosive, durable materials.

This main control board is the electronic module that manages your appliance's functions and user inputs, restoring normal operation when the board has failed. It replaces the appliance's primary logic/control circuit to allow proper control of cycles and features. What it does

• Interprets control panel commands and runs the appliance's programmed cycles
• Manages timing, sensors, and power distribution to subsystems
• Can resolve symptoms like unresponsive controls, erratic operation, or failure to start when the board is the fault
• Works with door, temperature, and user-interface signals to coordinate appliance functions

• One main electronic control board

• Disconnect power before attempting replacement to avoid shock or damage
• Handle the board by edges and avoid touching circuits or components
• Verify connectors and mating harnesses are fully seated during reassembly

This main electronic control board regulates the refrigerator's core functions so the unit runs reliably. Replacing a failed control board restores electronic control over cooling, defrost cycles, lights and user interface responses. What it does:

• Manages compressor and fan operation to control temperature
• Runs automatic defrost and associated heater timing
• Powers/display and processes user inputs for settings and diagnostics
• Coordinates dispenser, lights and other electrically controlled features
• Can stop erratic or intermittent operation caused by a faulty control board

• Disconnect power to the appliance before starting work to avoid shock
• Handle the board carefully and avoid touching contacts; use anti-static precautions if available
• Verify connector alignment and secure all wiring harnesses during reassembly

This is a genuine Frigidaire control board designed for ovens. The control board is the heart of the oven and allows the user to control things like oven temperature and function. If the board is damaged, it will not operate correctly and users may experience intermittent operation or have a inoperable oven.The oven control board is protected from most sources of damage by a surrounding metal frame. However, prolonged exposure to moisture or heat can damage the board. The electrical contacts will also degrade over time, leading to eventual need to replace the board. Replacing the board will require unplugging the oven or flipping the circuit breaker. Next, the user should remove the cowling around the oven display to expose the old board. Take note of the wiring connections and their location/orientation, remove them, remove the screws, and then install the new board following the same steps in reverse order.This OEM control board is sold individually. It is compatible with ovens from Frigidaire and Electrolux.