Cam Sink Parts

Color: Grey

The Spacer is an OEM part for Frigidaire ranges and ovens. This part provides the necessary clearance between the oven door handle and the door itself, preventing friction and wear while ensuring the handle is securely attached and easy to use. This small but crucial component aids in the proper functioning of the oven door, making it easier and safer to open and close without exerting extra force.

Causes of a bad Spacer include mechanical stress leading to cracks or breaks, improper installation that may result in loosening over time, and degradation from heat exposure and frequent use.

Symptoms of a failing Spacer include:

• Loose oven door handle.
• Difficulty in opening or closing the oven door.
• Visible gaps or misalignment of the door handle.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door stop limits the door's travel to its intended range, helping prevent overextension that can stress hinges or damage adjacent cabinetry. Replacing a worn or broken stop restores smooth, controlled door operation.

• Limits door opening/closing travel to protect hinges and alignment
• Helps maintain proper seal and fit by preventing overextension
• Replaces cracked, worn, or missing stop that allows excess movement
• Typical symptoms include door opening too far, a hard "clunk" at full travel, or visible damage to the stop

• Disconnect power; also shut off the water supply
• Support the door while servicing the hinge/stop to avoid strain
• Note the original orientation and transfer/secure fasteners firmly
• Open/close the door slowly to ensure smooth movement and proper stop action

The Closing Cam is an OEM part for Whirlpool refrigerators. The closing cam works with the door hinge and latch mechanism to make sure the refrigerator door closes securely.  

Causes of a bad closing cam can be normal wear and tear over time, excessive strain placed on the hinge areas, or damage from accidental impacts.

Symptoms of a bad closing cam include:

• Doors that do not fully close or latch properly
• Difficulty closing or opening the doors
• Increased energy costs from poor insulation
• Fruits and vegetables spoiling more quickly

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This cam-door is the small pivoting cam that helps a washer/dryer or laundry door latch and swing smoothly. Replacing a worn or broken cam restores proper door movement and helps the door close and seal reliably. What it does:

• Acts as the pivot/latch cam that guides the appliance door during opening and closing.
• Helps the door engage the latch and maintain correct alignment.
• Commonly used to stop a door from hanging, binding, or failing to stay closed.
• Can reduce door noise or catching caused by a damaged cam.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Support the door or cabinet panel during removal to prevent dropping or damage.
• Remove the door or access panel and replace the cam using basic hand tools; keep track of fasteners.
• After reassembly, check door operation and latch engagement before returning the appliance to service.

This rivet assembly is a direct-replacement fastening piece used to secure appliance panels and components, restoring a stable, rattle-free fit and preventing movement caused by worn or broken rivets. What it does:

• Secures panels, brackets, or component mounts to restore proper alignment and support
• Stops rattling, vibration, or loose hardware caused by damaged or missing rivets
• Provides a durable mechanical fastener where original rivets have sheared or loosened
• Helps maintain safe operation by keeping parts properly retained

• Disconnect power (and gas/water if applicable) before attempting any repairs
• Removal may require drilling out the old rivet; installation typically needs a rivet gun or equivalent tool
• Keep hardware orientation the same as the original; replace any damaged surrounding parts

The Refrigerator Upper Hinge Riser is an essential component for maintaining the functionality of your Samsung refrigerator. This genuine OEM part ensures a perfect fit, providing reliable support for the upper hinge assembly. Designed specifically for Samsung refrigerator models, it enhances the stability and alignment of the refrigerator door, reducing wear and tear over time. The Upper Hinge Riser facilitates smoother door operation, preventing sagging and ensuring that your fridge door stays securely in place. Installing this part helps to prolong the lifespan of your appliance by addressing common hinge issues effectively. With easy installation, you can restore your refrigerator's performance without the need for professional assistance. Choose the Refrigerator Upper Hinge Riser to maintain the optimal operation of your Samsung refrigerator, ensuring a better user experience and extending the durability of your appliance.

This door hinge restores smooth, controlled door movement and a secure close. Replacing a worn hinge helps the door align properly and engage the gasket or latch for reliable everyday operation.

• Supports and pivots the door on its side
• Provides tension for controlled opening and closing
• Helps keep the door fully closed and properly aligned with the cabinet
• Common signs of wear: door won't close completely, drops open too quickly, feels loose or misaligned, or creaks

• Disconnect power (and gas, if applicable) before servicing; allow the appliance to cool
• Remove or support the door before detaching the hinge; note orientation and side
• Use caution—the hinge is spring-loaded; release and re-engage tension slowly
• After installation, check door alignment, closing action, and seal/latch engagement

This reinforcement spacer maintains the correct gap and supports the joint between mating parts in your appliance. Replacing a worn or missing spacer helps keep panels, trim, or brackets aligned for a solid fit and smooth operation.

• Maintains proper spacing and alignment between components to prevent rubbing or distortion
• Reinforces mounting points to distribute fastener load and reduce cracking around holes
• Helps reduce rattles and looseness; promotes tight, even gaps
• Common signs include a missing/broken spacer, wobbly panels/trim, rattling noises, or visible misalignment

• Disconnect power; allow the appliance to cool completely. For gas units, shut off the gas supply
• Access the affected area and note the spacer's orientation before removal
• Reuse original hardware and install the spacer in the same position; do not overtighten fasteners
• Reassemble, check clearances and alignment, then test operation

This door closer plate is a hinge component that helps your refrigerator door swing closed and seal properly. Replacing a worn plate restores smooth door action and supports a reliable seal to help maintain interior temperatures.

• Guides the hinge/cam for self-closing action and a consistent door stop
• Helps the door close fully and stay shut to protect the gasket seal
• Common symptoms include clicking/grinding at the hinge, door drifting open, or misalignment
• A weak seal from incomplete closing can contribute to frost or condensation

• Unplug the refrigerator; turn off the water supply
• Remove items from the door and support the door to prevent strain on the hinge
• Remove hinge cover and fasteners, separate the hinge as directed by your manual, and replace the closer plate; align with the mating cam
• Reassemble, level/align the door, and verify smooth closing and gasket contact

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

Refrigerator Cam Hinge Riser Low Right is an essential component designed to enhance the functionality of your Samsung refrigerator. This genuine OEM part ensures smooth and stable operation of the refrigerator doors by providing the necessary support and alignment. Made specifically for Samsung refrigerator models, it guarantees a perfect fit and seamless integration with your appliance. The CAM HINGE-RISER LOW R helps prevent door misalignment and reduces wear and tear, extending the lifespan of your refrigerator. Its durable construction withstands regular use, ensuring long-term performance and reliability. Installing this genuine OEM part is straightforward, allowing you to quickly restore your refrigerator's functionality without hassle. By choosing the Refrigerator Cam Hinge Riser Low Right, you can maintain the efficiency and appearance of your Samsung refrigerator, ensuring a better overall user experience.

This hinge bearing supports the freezer door on the hinge pin so it swings smoothly and stays aligned. Replacing a worn bearing can stop scraping or sagging and help restore proper door movement and sealing.

• Provides a low-friction surface between the hinge pin and door
• Helps maintain correct door height and alignment for a reliable seal
• Wear symptoms include squeaking/scraping, door drop or wobble, and difficulty closing
• Replace if the original bearing is cracked, flattened, or missing

• Disconnect power and remove items from the freezer door before starting
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Slide the old bearing off the hinge pin and install the new bearing in the same orientation
• Reassemble, then check door alignment and gasket contact; adjust as needed

This replacement bracket secures and supports a component in your appliance. Replace a bent, cracked, or missing bracket to restore proper alignment and stable mounting, helping reduce vibration, rattling, and premature wear on connected parts. What it does:

• Holds the related component firmly in place
• Helps maintain correct alignment of the assembly
• Reduces unwanted movement, vibration, and noise
• Common signs it may be needed: loose or shifting component, rattling sounds, visible damage, or a missing bracket

• 1 bracket

• Disconnect power and shut off water or gas supply before servicing
• Wear cut-resistant gloves; brackets and surrounding panels may have sharp edges
• Note the original orientation and reuse existing fasteners as applicable
• After installation, verify alignment and secure fit per your model's parts diagram

This door closing cam mounts at the bottom of the refrigerator door and mates with the hinge cam to raise and lower the door as it swings, promoting smooth self-closing action and a reliable gasket seal.

• Provides lift-and-drop detent at the lower hinge to guide door movement
• Helps the door self-close in the final inches for a consistent seal
• Supports proper door alignment to reduce air leaks and temperature fluctuations
• Common symptoms: door won't self-close, pops/clicks at the hinge, sags or binds, poor seal or moisture around the door

• Disconnect power and remove items from the door to reduce weight
• Support the door; remove hinge cover and lower hinge/pin, then lift the door off carefully
• Replace the cam on the door/hinge as designed; inspect the mating cam and hinge pin and lightly lubricate
• Reinstall, level, and verify smooth closing and proper gasket contact