Loose Band Wire Connection Parts

This element wire harness connects the heating element to your range or wall oven's internal wiring, delivering power for proper heating. Replace a burned or brittle harness to restore consistent oven performance and safe, reliable operation.

• Supplies electrical current from the appliance wiring to the heating element
• Maintains secure, heat-resistant connections at the element terminals
• A damaged harness can cause no heat, slow preheats, or intermittent heating
• Visual clues include burned insulation, discoloration, or loose/melted connectors at the element

• Disconnect power at the breaker and allow the oven to cool completely
• Access element connections from the rear panel or inside the oven (model dependent)
• Note routing; move one connection at a time to the new harness and ensure terminals are fully seated
• Route wires away from sharp edges and hot surfaces; verify secure connections before restoring power

This sump clamp secures the dishwasher's sump connection at the base of the tub, helping maintain a tight, leak-resistant seal. Replacing a weakened or corroded clamp can help stop drips and keep the wash system stable.

• Secures the sump connection so it stays firmly in place
• Applies even clamping force to help maintain a watertight seal
• Helps prevent leaks or puddles beneath the dishwasher
• Typical signs include water leaking from the bottom, a loose connection, or a rusted/broken clamp

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and access the sump area; have towels or a pan ready for residual water
• Loosen and remove the old clamp; inspect mating surfaces and the sump seal/gasket and replace if worn
• Position the new clamp squarely and tighten evenly—do not overtighten; run a brief test and check for leaks

Includes 12 retainers.

The Nut is an OEM replacement part for Whirlpool refrigerators. This small yet essential component is used to secure various parts of the refrigerator, such as shelves, panels, or brackets, ensuring stability and proper alignment. Its durable design ensures reliable performance in the demanding environment of a refrigerator.

Causes of a bad or missing Nut can include wear over time, accidental stripping of threads, or loss during maintenance or repairs. A damaged or missing nut can lead to loose components and reduced functionality.

Symptoms of a bad or missing Nut include:

• Loose or wobbly shelves, brackets, or panels
• Difficulty keeping refrigerator components securely in place
• Rattling or unusual noises during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement clip secures components within your appliance. Replacing a broken, bent, or missing clip restores a firm hold on panels or assemblies to prevent shifting and reduce vibration noise.

• Holds specified parts or panels in place where a clip is called out in the assembly
• Helps maintain proper alignment and minimizes rattles/vibration
• Direct replacement for a damaged or missing clip
• Common symptoms: loose or misaligned parts, rattling during operation, clip visibly broken or missing

• Disconnect power before service; also shut off gas/water supplies
• Note the original clip orientation and placement; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid overbending or deforming the clip
• Inspect mating parts for wear or damage and ensure the clip seats fully

Kit of 24 clips

This replacement power cord restores the electrical connection to your appliance so it can receive consistent power and operate safely. It's a direct-fit service part used when the original cord is damaged or no longer supplying power. What it does:

• Provides the main electrical connection from the wall outlet to the appliance
• Replaces frayed, cut, or melted cord insulation that can cause power loss or shorts
• Stops intermittent or no-power symptoms caused by a damaged cord
• Restores safe, reliable power delivery when the original cord is faulty

• Always disconnect power at the breaker or unplug the appliance before installation
• Route and secure the cord away from sharp edges, moving parts and high-heat areas

The Power Cord is an OEM part for Whirlpool washing machines. It delivers electrical power from the wall outlet to internal components inside the washer cabinet. Made of insulated copper wiring housed within a tough flexible jacket, this cord prevents shocks and ensures reliable power delivery.

Causes can include normal wear over many machine cycles. Rodent chewing, cracking from overly tight bends, or cuts from sharp metal edges are also possible.

Symptoms of a failed power cord include:

• No power to washer control board or motor
• Tripped breaker after plugging washer in
• Bare or frayed copper wiring exposed
• Brittle, cracked cord jacket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This cord set is a direct-replacement power cord that restores electrical connection to the appliance, letting it receive safe, consistent power when the original cord is damaged or worn. What it does:

• Provides the appliance's main AC connection so it can power on and operate
• Replaces frayed, cut, or melted cords that cause intermittent power or arcing
• Prevents unsafe wiring conditions from exposed conductors or loose connections
• Restores a secure plug/cable interface when the cord or plug is damaged

• One replacement cord set

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Verify the replacement cord matches the original in wire count, connector type, and amp rating
• Tighten terminal screws securely and route the cord to avoid pinching or contact with hot components

This hose clamp secures a rubber or plastic hose to its fitting on your appliance, maintaining a tight, leak-resistant seal under vibration and pressure. Replace when the old clamp is rusted, bent, or no longer holds tension. What it does:

• Clamps around a hose to grip the fitting and seal the joint
• Helps prevent drips, leaks, and hose blow-off at the connection
• Restores secure clamping force when the original is worn or damaged
• Common symptoms: water at the connection, hose slipping off, visible corrosion or distortion

• 1 hose clamp

• Disconnect power and shut off the water supply before servicing
• Slide clamp onto hose, seat hose fully on the fitting, then position clamp just behind the bead/raised lip
• Tighten or compress evenly with the appropriate tool; avoid overtightening that could damage the hose
• After reassembly, run a short test and inspect for leaks

This small hardware clamp is used on select refrigerators to secure tubing or wiring to the cabinet or frame. Replaces a missing or damaged clamp to keep lines stable, reduce vibration, and help prevent rubbing or leaks.

• Secures small water tubing or electrical harnesses along the cabinet/frame
• Helps prevent vibration, rattling, and abrasion of lines
• Maintains correct routing to keep lines clear of moving or hot components
• Common clues: loose or noisy lines, chafing marks, or moisture near tubing connections

• Unplug the appliance and shut off the water supply before servicing
• Note the original location and routing; take a photo for reference
• Reuse the existing mounting screw/fastener if required; tighten only enough to hold without crushing tubing
• Restore power and water, then run and inspect for vibration and leaks

This genuine replacement power cord restores electrical connection to your appliance so it can safely receive power. It replaces a damaged or worn cord to help eliminate power loss and reduce electrical hazards. What it does:

• Provides the electrical connection between the appliance and your home's power supply
• Replaces frayed, cracked, or burned cord insulation and damaged plugs
• Helps stop intermittent power issues caused by a faulty cord or connector
• Restores safe, reliable power routing when the original cord is compromised

• Always disconnect power at the breaker or unplug the appliance before installing
• Follow the appliance wiring diagram and route the cord to avoid heat or pinch points
• Secure strain relief and connectors per the manufacturer's instructions

Replacement wire harness that restores electrical connections between the appliance control, power and components for reliable operation and correct signaling. Use this complete wiring assembly when damaged wires or connectors cause power or control issues. What it does:

• Routes power and signal conductors between the control board, switches, motors and sensors.
• Replaces damaged, frayed or melted wiring and broken connectors that can cause intermittent operation, no-start or control failures.
• Restores factory-style plug connections and routing to help prevent miswiring and shorts.
• Matches the original connector shapes and wire colors for straightforward replacement.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Remove and replace the harness by disconnecting connectors at the control and components; handle connectors by the plastic bodies, not the wires.
• Route the harness along the original path and secure with existing clips or fasteners to prevent rubbing or heat exposure.