316244490 Parts

This carburetor is a device for supplying a two-cycle engine with a mixture of air and fuel. This part comes pre-assembled and has a plastic choke lever along with a metal body. The primary purpose of a carburetor is to mix the right amount of fuel with air so that the engine runs properly. If enough fuel is not mixed with the air, the engine runs lean and can either stop running or gets damaged. On the other hand, if too much fuel is mixed with air, the engine runs rich, and it either floods, runs poorly, runs very smoky, or wastes fuel. The carburetor is in charge of getting the right mixture. If the carburetor is clogged, the engine will not get enough fuel. It may not start or may run rough. The procedure to replace the carburetor is quick and easy, taking only around 15 minutes, but it is recommended to work in a ventilated area. This carburetor works with outdoor power tools like the trimmer, leaf blower, and tiller. It is compatible with specific products from popular brands like Craftsman, MTD, Murray, and Troy-Bilt. It is sold individually and is supplied directly from the original equipment manufacturer.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

A carburetor gasket is a thin rubber material that provides a seal between two parts. Its primary purpose is to prevent fuel and air leaks. This gasket is installed between the air cleaner and the carburetor. Over time, it can crack and tear due to heat and fuel exposure. When this happens, the carburetor may produce the wrong combustible mixture for the engine. In return, the engine may experience rough idling and flooding. A carburetor gasket replacement is necessary. MTD makes this carburetor gasket replacement. It is manufactured to fit string trimmer, leaf blower and tiller made by MTD, Bolens, Troy-Bilt, and Craftsman. This brand-new carburetor gasket is sold individually. A fully assembled carburetor and O-ring are sold separately.

This is a replacement spark plug that is designed specifically to be used with select string trimmers. the spark plug is connected to the ignition module and is responsible for creating the spark that starts the internal combustion engine. Over time, the electrode on the spark plug will wear down. Other issues can also arise that cause the spark plug to foul or stop working. Spark plugs are part of routine maintenance on any engine, but most owners keep a spare or two around just in case of emergencies. In the event that the spark plug is bad, the engine will not start. This genuine OEM spark plug is manufactured by MTD and designed for use in select trimmers. It is compatible with over 50 models of string trimmers from MTD, Bolens, Murray, Troy-Bilt, Yard Man, and Cut Cadet. Owners will need to consult their product diagram or manual to find the exact gap for the spark plug when replacing them. Many models claim to come pre-gapped, but they can settle during shipping and should always be re-gapped prior to installation. This is sold as an individual unit. Be sure to wear gloves for hand protection when replacing spark plugs and performing other maintenance.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This part is a replacement gear box assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or damaged gear box assembly in a variety of tiller models. The gear box assembly helps to power and drive the tiller's tines, enabling them to rotate. If this part is damaged the tines may not function, rendering the equipment inoperable. This gear box assembly includes the gears and axle. Proper tools will be needed to install this part. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this gear box assembly, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this gear box assembly is suitable for use on several different models of tillers manufactured by MTD, Bolens, Troy-Bilt, and Cub Cadet. This is a genuine part made of high-quality, durable materials and is sold individually.

This is a fully-threaded hex tap screw that can be used in a wide range of machines from many of the top brands making lawn and garden equipment. The screw is used to help fasten pieces of the machine together and to provide a tight connection. If the screw is damaged in some way or is missing, it can cause a range of problems in the machine. Problems with the screw might cause the machine to not hold together properly. It could cause added vibration in the machine.The hex tap screw is made from metal and it should last for a long time without needing to be replaced. However, problems can happen. The head could become damaged and difficult to turn, which will require a replacement before the problem worsens. The threads could be stripped, or the screw could have become corroded. It might also be lost and will need to be replaced.The hex tap screw can work with machines from Craftsman, Ryobi, Bolens, Troy-Bilt, MTD, Husky, Yard Machines, and Yard-Man. It is sold individually and is a genuine OEM replacement part.

The clutch assembly uses centrifugal force to connect the shafts and create the drive shaft motion that powers the machine. The drive shaft nests inside the other shaft, and over time these parts can wear and become damaged with regular use. Today's parts can even continue to function long past when they should, so it may not be apparent that a clutch assembly needs to be replaced until the entire unit is bad. If the engine is not performing as it should or if the drive shaft seems unstable, it may be time to replace the clutch assembly. This genuine OEM part includes everything needed for the job. This OEM clutch replacement is designed for use with various cultivators, edgers, and trimmers. It can be used on machines from MTD, RYOBI, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, Murray, and Husky. This assembly includes the clutch, clutch drum, washer, and left-hand threaded screw. Always disengage the spark plug and allow the engine to cool completely before beginning repairs.

This fuel cap assembly fits on the lawn tractor fuel tank to keep the fuel inside and debris outside. The part is red and has a gas pump embossed on it for added identification. The top of the cap also features vent slots to allow hot air to escape and prevent heat expansion. It features a gasket under the cap to keep gas from sloshing out during operation. The fuel cap assembly is made of heavy-duty plastic that can fade and crack due to the elements. Removal and replacement are as simple as taking the old cap off and putting the new cap on. Hand-tighten to prevent gas from leaking. Never over-fill the fuel tank. Leave room for the oil additive if it is not mixed before fueling. This fuel cap assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is sold as an individual unit. This fuel cap is designed for use in lawnmowers and lawn tractors manufactured by MTD, Ryobi, Troy-Bilt, Bolens, Yard-Man Yard Machines, Cub Cadet, and Murray.

This genuine OEM replacement part is a push cap designed for snowblower, tiller, and edger wheel assemblies. A push cap is a special type of nut, or fastener, that helps to hold unthreaded shafts in place. Although small, this push cap helps to secure the wheel to the axle. Push caps are most commonly damaged if the operator uses their appliance in rough terrain. If damaged, it can fall off, causing the wheel to also fall off. Replacing push caps is an easy repair as they attach to the outside of the wheel assembly. The only hardware required to make this repair is a nut driver. If you do not have a nut driver, a pair of pliers can also be used to attach the new push cap. This part is a high-quality replacement part meant for Yard Man, Husky, Ryobi, Yard Machines, Troy-Bilt, MTD, Bolens, and Cub Cadet appliances. It is sourced direct from its original manufacturer and ships individually.

This replacement part is a pin lynch. This is a genuine replacement part made by MTD. This part is small but important to ensure that the axle or shaft is working properly during use.A new pin lynch might be needed if the current one is missing or damaged. It is not uncommon for the pin to be stripped down over time due to normal wear and tear in the machine. Often times the pin also gets lodged into place and should be replaced if this ever occurs. Wear work gloves when completing this repair to prevent injury. The engine should be completely turned off and cooled down. This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.

This tine assembly is a genuine MTD part, sold individually. This tine assembly can be used as a replacement part in a tiller. The purpose of the tine assembly in a tiller is to bore into the soil and loosen up packed dirt so that plants and greenery can be kept healthy and verdant.If the tines are dented, cracked, warped, eroded, or otherwise damaged to the point that they cannot effectively bore into the soil and serve their function, the tine assembly should be removed and replaced by this genuine OEM replacement part before using the tiller again.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This tine assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Cub Cadet, and Yard Machines.

This tine assembly is a genuine MTD part, sold individually. This tine assembly can be used as a replacement part in a tiller or a string trimmer. The purpose of the tine assembly in a tiller or a string trimmer is to provide the appliance with the proper blades to cut through and loosen soil in order to keep the lawn of the operator healthy.The tine assembly in a tiller or a string trimmer might need to be replaced at some point within the standard lifespan of the outdoor appliance. This could occur if the tine assembly has been punctured, warped, dented, cracked, or eroded to the point that the tines are no longer as functional as they once were. If this is the case, the tine assembly should be removed and replaced by this genuine OEM replacement part before using the tiller or the string trimmer again.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This tine assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Man.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.