Gfwh1400dww Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Water Inlet Valve is an OEM part for GE washing machines. It controls the flow of water into the washer during the fill cycles. The valve opens and closes to allow the correct amount of water to enter the machine based on the selected wash cycle and settings.

You should replace this water inlet valve if it becomes defective. A bad water inlet valve can cause several issues such as improper water levels, slow filling, or no water entering the washer at all. These problems can be due to sediment build-up, electrical faults, or mechanical wear.

Symptoms of a bad water inlet valve include:

• Washer not filling with water
• Slow filling or low water pressure
• Leaking or dripping water from the valve area
• Incorrect water levels in the drum

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE pump is an OEM replacement part responsible for removing wastewater from the washing machine during the drain cycle. It pumps out the soiled water from the washer's tub, ensuring that it is expelled through the drain hose and into the plumbing system or utility sink. The pump consists of an electric motor and an impeller that move the water effectively.

Causes of a bad pump can include clogging from debris or lint, wear and tear from regular use, or damage to the pump impeller or motor. Exposure to harsh chemicals or overloading the washer can also contribute to pump failure.

Symptoms of a bad pump include:

• Water not draining from the washer
• Unusual noises such as humming or grinding during the drain cycle
• Error codes related to drainage issues
• Water leaking from the bottom of the washer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Outer Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp ensures that the seal is tightly held in place, preventing water from leaking out of the front load washer during operation.  

Causes of a bad Outer Door Boot Seal Clamp can range from corrosion due to exposure to moisture and detergents, to physical damage from improper installation or removal of the door seal.  

Symptoms of a malfunctioning Outer Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or detaching from the front panel
• Visible damage or corrosion on the clamp, compromising its integrity

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Lock Assembly is an OEM replacement part for GE washing machines. It secures the washer door safely closed during operation. The assembly features a locking mechanism that withstands vigorous cycles while preventing small hands or objects from opening it inadvertently.

Causes of a bad door lock can include worn parts from repetitive use that become misaligned and fail to lock properly. Damage from forced opening can deform lock components.

Symptoms of a bad door lock assembly include:

• The door popping or creeping open during cycles
• Difficulty latching or hearing the door lock "click" closed
• Error codes related to an unsecured door

This OEM part is also compatible with Hotpoint, RCA, and select Kenmore models.

The Door Gasket is an OEM replacement part for GE front-load washing machines. It is installed around the perimeter of the machine's door, creating a watertight seal when the door is closed. This prevents water from leaking out of the washing machine during operation, ensuring efficient and mess-free wash cycles.

Symptoms of a bad Door Gasket include:

• Water leakage around the washing machine door
• Mold or mildew buildup on the gasket
• Visible damage, such as cracks, tears, or wear
• The washing machine door not closing properly

Causes for a malfunctioning Door Gasket can include regular wear and tear, exposure to harsh detergents or chemicals, or buildup of debris that compromises the seal's integrity.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models

The Driving Belt is an OEM part for GE washing machines. This part connects the motor to the drum, facilitating the drum's movement during the wash and spin cycles, ensuring your laundry is cleaned effectively.

Common causes of a bad driving belt include normal wear and tear, overloading the washer, or exposure to high heat or friction. 

Symptoms of a bad Driving Belt include:

• Drum not spinning or agitating
• Washer making unusual noises during operation
• Burning smell from the washer
• Visible cracks or wear on the belt

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drive Pulley Kit is an OEM part for GE washing machines. The drive pulley works by transferring the motor's power to the drum via the drive belt, ensuring the drum rotates properly during the wash and spin cycles.

Causes of a bad drive pulley can include wear and tear over time, damage due to overloading the washer, or issues such as misalignment or loose components.  

Symptoms of a bad drive pulley include:

• Loud, unusual noises during operation
• The drum not spinning or agitating
• The washer not completing cycles properly
• Visible damage or wear on the pulley

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Inner Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp secures the door boot seal, ensuring it stays in place and forms a watertight barrier between the washer door and drum.  

Causes of a bad clamp can include regular wear and tear, corrosion from detergent and water exposure, or physical damage from rough handling. 

Symptoms of a bad inner door boot seal clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or not staying in place
• The washing machine door not closing properly
• Visible rust or damage on the clamp

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This drain pump filter traps lint, coins, and small debris before they reach the pump, helping your washer drain properly and protecting the pump from damage. Replace a broken or clogged filter if you notice slow draining or a leak at the filter access.

• Screens out debris before it reaches the drain pump
• Helps maintain proper draining performance
• Common symptoms of a failed or missing filter: not draining/slow drain, leak at the filter access, or pump noise from debris
• Prevents hard objects from entering the pump and causing damage

• Disconnect power and turn off water before servicing
• Expect residual water; place towels or a shallow pan under the filter area
• Access the filter, unscrew and remove the old filter, and clear any debris from the housing
• Install the new filter and hand-tighten to seal; run a short drain cycle and check for leaks

This suspension spring supports and stabilizes the washer tub, controlling movement during wash and spin. Replacing a weak or broken spring helps restore balance, reduce vibration, and prevent the tub from leaning or striking the cabinet.

• Supports the tub assembly within the cabinet and carries load
• Limits tub motion to reduce shaking and out-of-balance interruptions
• A stretched or broken spring can cause excessive vibration, banging, or a low/leaning tub
• Visual signs include broken coils or uneven tub height

• Disconnect power; turn off water and move the washer for safe access
• Springs are under tension—support the tub and wear hand/eye protection
• Note the original spring's location and orientation; reinstall in the same position
• After replacement, ensure the tub sits level and clears the cabinet on all sides

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This interface board mounts behind the washer's control panel and reads your button/knob inputs. Replacing a failed UI board restores responsive controls, correct cycle selection, and indicator lights so the washer can start and run as expected.

• Interprets user inputs from the control panel and selector(s)
• Communicates selections to the main control to run chosen cycles/options
• Drives status lights or display during operation
• Typical failure symptoms: unresponsive controls, lights/display not illuminating, cannot start or change cycles, intermittent/erratic inputs

• Disconnect power to the appliance before servicing; follow ESD precautions and handle the board by the edges
• Access the board by removing the console/control panel; note screw locations and take photos of wiring
• Transfer wire connectors one at a time to the new board to prevent miswiring; ensure all harnesses are fully seated
• Reassemble the console and restore power; test all buttons and indicators

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

The TUB SEAL is an OEM component specifically designed for GE washers. It is a rubber gasket located between the inner and outer wash tubs designed to prevent leaks. During cycles, the seal withstands contact with fast spinning and surging water pressure to maintain a watertight barrier. 

Symptoms of a bad tub seal include: 

• Puddles, drips, or leaks visible beneath the unit during or after cycles
• Excess moisture trapped between the inner and outer tubs
• Mineral or soap film buildup indicating escaping water 

Causes can be cracks developing from age and repetitive flexing during cycles, or deformities in the rubber preventing proper compression.

Replace yours today with this genuine OEM GE part to ensure a dependable water containment solution. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

This stacking kit secures a compatible dryer to a matching washer to create a safe, space-saving stacked laundry configuration. It helps stabilize the dryer and reduces movement during use for a more reliable setup. What it does:

• Provides brackets and mounting hardware to fasten the dryer to the washer
• Helps prevent the dryer from shifting or tipping when the washer is running
• Improves overall stability of stacked laundry appliances during normal operation
• Reduces vibration-related movement that can cause noise or misalignment

• Disconnect power to both appliances before installing and follow all manufacturer instructions
• Use only on compatible washer/dryer pairs
• Tighten hardware securely but avoid overtightening; follow torque guidance in OEM instructions