Prd48jdsgu Parts

The Spark Ignition Switch is an OEM part for Bosch ranges and cooktops. It controls the ignition of surface burner flames by emitting an electrical spark when activated.

Causes of a bad switch can be general wear and fatigue over thousands of start cycles. Exposure to moisture, dust or metal debris could also damage electrical components internally.

Symptoms of a bad spark ignition switch include:

• Burners failing to light even when valves are turned on
• Intermittent or irregular lighting of some burners
• No electrical sparks emitted from the ignition electrode

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

Note: Kit includes 4 feet and a tube of RTV with instructions.

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

The Screw is an OEM part for Bosch ranges. It plays a crucial role in connecting and securing range components and panels. Over time, screws can strip, corrode, or break, preventing tight connections and proper alignment of parts.

Causes can include normal wear and tear over time, as well as damage during repair or maintenance. Replacing missing or faulty screws with genuine OEM parts is important to ensure the range operates as designed and presents no safety issues.

Symptoms of bad or missing screws include:

• Doors, panels, or panels not sitting flush
• Components detaching or coming loose
• Alignment issues between connected parts
• Reduced structural integrity

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

The Solenoid Valve is an OEM part for Bosch ranges. Located inside the control panel, the solenoid valve regulates gas to individual burners during the cooking cycle. It opens and closes electrically to direct fuel when its paired control knob is turned on.

Symptoms of a bad solenoid valve include:

• Inability to ignite or maintain a flame on specific burners 
• Burners failing to respond to control settings
• Hesitation or delay in burner engagement
• Range functions in an unpredictable manner

Causes can involve normal wear of moving internal parts, mineral buildup inhibiting valve movement, or physical damage. Failure reduces the range's functionality and safety.

This OEM Bosch part is also compatible with Thermador and Gaggenau models.

The Drip Tray is an OEM part for Bosch ranges. The drip tray catches any liquid spills, grease, or condensation generated during the cooking process. Its open design allows easy access for cleaning while contained drainage protects components.

Causes of a faulty drip tray can include cracks or punctures from impact, melting or warping from high heat exposure over time, or general damage during cleaning.

Symptoms of a bad range drip tray include:

• Grease or liquidAccumulation outside of the drip tray area
• Dripping or potential fire hazards if material collects on heating elements below
• Difficulty removing the drip tray for cleaning due to deformities or breaks

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This temperature regulator is the mechanical thermostat that controls oven heat. It senses cavity temperature and cycles the heat source on and off to reach and maintain your set temperature for consistent baking and roasting performance. What it does

• Senses oven temperature via a capillary bulb and tube
• Opens and closes internal contacts to control the heating source
• Maintains the selected temperature during cooking cycles
• Help resolve: oven not reaching set temp, overheating or wide swings, uneven baking, or unresponsive temperature control

• 1 temperature regulator

• Disconnect power; shut off gas. Allow the appliance to cool completely
• Note the original routing of the sensing bulb and capillary; reinstall the new one in the same path and clips. Do not kink, sharply bend, cut, or shorten the tube
• Transfer any knob/shaft components as needed and align properly
• After installation, verify temperature with an oven thermometer and adjust per service instructions if applicable

The Water Tank is an OEM part for Bosch steam ovens. This part is designed to hold and supply water for the steam generation process in your oven, providing a source of water for steam cooking. 

A bad water tank can occur due to wear and tear, accidental damage, or improper maintenance. Signs of a faulty water tank include leaks, cracks, or difficulty in filling or emptying the tank.

Symptoms of a bad water tank include:

• Water leaks in the oven or surrounding areas
• Cracks or visible damage to the tank 
• Difficulty in filling or emptying the tank 

Replace your worn-out or damaged water tank with this genuine OEM Bosch part to restore your range. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This Broil Heating Element is an OEM part for Bosch Ranges. It is responsible for providing high heat for broiling functions and evenly distributing heat within the oven cavity. It ensures efficient broiling performance for cooking various dishes.

A common issue with a malfunctioning Broil Heating Element is wear and tear over time, leading to potential element damage or failure. Frequent usage, or heating irregularities can compromise its function.

Symptoms of a defective Broil Heating Element may include:

• Uneven broiling or cooking results
• Inadequate heating or failure to reach desired temperatures
• Visible damage or signs of wear on the heating element

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

A replacement high-temperature cut-out that helps protect ovens by interrupting power if internal temperatures rise above safe levels. Restores the appliance's over-temperature protection so heating elements can be safely shut off when needed. What it does:

• Monitors oven temperature and opens the circuit if temperatures exceed a safe threshold to prevent overheating.
• Stops power to heating elements when tripped, preventing further temperature rise.
• Common symptoms of a failing cut-out: oven won't heat, continuous heating or no control over temperature, or oven shuts off unexpectedly.
• Used as a safety device in the oven's temperature-control system.

• Disconnect power at the breaker and allow the appliance to cool completely before servicing.
• Replace with the exact OEM cut-out and secure all wiring connections.

The Re-Ignition Spark Module is an OEM replacement part Bosch ranges. It is an electronic component that generates sparks to reliably light the burners on a gas cooktop. Consistent sparking is necessary for fully lighting the burner flames and facilitating safe and efficient cooking operation.

Causes of a bad spark module can include normal component wear over time or damage from exposure to moisture or other contaminants. Improper cleaning methods could potentially impact performance.  

Symptoms of a bad spark module include:

• Burners not lighting or sparking when the knob is turned 
• Unreliable or intermittent lighting requiring multiple attempts
• Burner flames that emit an inconsistent or unstable pattern
• Sparks appearing outside of the burner ring pose a safety risk

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore model

This control unit is the central electronic board that manages your appliance's functions and cycles. Replacing a failed module can restore responsive controls and reliable operation when the machine won't start, stops mid-cycle, or shows repeated error codes. What it does:

• Directs timing and power to components such as motors, pumps, valves, or heaters
• Interprets inputs from the user controls and sensors to run the selected program
• Coordinates safety interlocks and built-in diagnostic routines
• Common failure symptoms include no start, unresponsive controls, random shutdowns, or persistent error codes

• 1 control unit

• Disconnect power (unplug or switch off the breaker) before servicing; shut off water supply if applicable
• Handle the board with ESD precautions; avoid touching components and contacts
• Photograph wiring and move connectors one at a time to the new board to maintain placement
• Ensure all harnesses are fully seated and the module is secured; restore power and run model-specific tests per the service documentation