Zdbr240nbs Parts

The Magnetic Gasket is an OEM part for GE refrigerators. This part is a flexible seal that runs along the edge of the refrigerator door, ensuring a tight closure. The magnetic gasket helps to maintain the internal temperature by preventing warm air from entering and cold air from escaping, thus enhancing energy efficiency and preserving food quality.

Causes of a bad magnetic gasket can include wear and tear over time, physical damage from frequent door openings and closings, or loss of magnetism which can weaken the seal.

Symptoms of a bad magnetic gasket include:

• The refrigerator door not closing properly
• Warm air leaking into the refrigerator
• Increased energy consumption
• Frost buildup inside the refrigerator
• Visible cracks or deformities in the gasket

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a power supply board used in refrigerators and beverage coolers. This component is used to manage and monitor temperatures and other settings related to the appliance. It is a part made up of many small components and any one of them can go bad and cause problems over time. If there is an issue with the power supply board, it will often cause the refrigerator to stop working. In this situation, the power supply board should be replaced.Basic tools will be needed to replace the refrigerator power supply board. It should also be unplugged before starting the replacement process. The location of this component may vary based on the appliance model. Often, it will be behind an access door on the back of the refrigerator. Unscrew the door to remove the original power supply board. Reinstall the wires and other components on the new part, install, and return power to the appliance.This is an authentic OEM replacement part that is sourced directly from the manufacturer. The power supply board is sold on an individual basis. It is designed to be used with refrigerators and wine and beverage coolers by General Electric.

This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. Replaces a failed start relay to restore compressor starting function and reduce hard-start symptoms. What it does:

• Provides the initial boost to the compressor motor during startup so the compressor can engage
• Commonly used when a fridge hums but the compressor won't start or cycles on and off
• Works with the compressor's start circuit; not a replacement for an overheat protector or run capacitor unless specified

• One start relay

• Disconnect power to the appliance before beginning any work
• Typically mounts on or near the compressor; remove access panel to reach compressor terminals
• Swap the old relay for the new unit, matching terminal positions; secure any clips or covers

This statement-style door handle replaces a damaged or worn refrigerator door handle and restores a secure, comfortable grip for opening and closing. It matches the original shape and finish for a clean, factory look. What it does:

• Replaces a cracked, broken or loose refrigerator door handle so you can open the door safely
• Restores proper grip and lever action for everyday use
• Hides cosmetic damage and returns the appliance to a finished appearance
• Fits the original handle mounting points for a straightforward swap

• Disconnect power to the appliance before starting; remove food and shelves as needed for access.
• Retain and reuse original screws/clips unless replacements are provided; only install hardware documented to fit.
• Use proper tools, avoid overtightening fasteners to prevent damage.

The Condenser Fan Motor is an OEM replacement part for GE refrigerators. It is designed to ensures proper airflow, dissipating heat and preventing the compressor from overheating. It helps to regulate the temperature inside the refrigerator, ensuring efficient operation and preservation of your food.

A bad condenser fan motor can occur due to various factors, including normal wear and tear, motor failure, or damage to the fan blades. If you notice symptoms such as unusual noises, warm temperature inside the refrigerator, or the compressor running excessively, it may indicate a need to replace the condenser fan motor.

Symptoms of a bad condenser fan motor include:

• Unusual noises coming from the condenser unit
• Warm temperature inside the refrigerator
• Excessive running of the compressor

Restore your refrigerator by replacing the faulty condenser fan motor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This overload protector helps safeguard the compressor by shutting it down during electrical overloads or overheating, preventing damage and improving appliance reliability. Fits select GE refrigerators and mounts on the compressor body. What it does:

• Senses excessive current or heat at the compressor and interrupts power to prevent burn-out
• Helps stop hard-starting compressors from running continuously when overloaded
• Works with the start device/relay as part of the compressor starting and protection circuit

• Disconnect power to the appliance before accessing the compressor or electrical components
• Mounted on the compressor; may require removing a rear access panel and repositioning the start device/relay
• Inspect the start relay and wiring harness while replacing the overload for best results

This short frame guide helps support and guide the refrigerator drawer or bin for smooth opening and stable operation. It replaces a worn or broken guide to restore proper alignment and reduce drawer sticking or wobble. What it does:

• Guides and supports the drawer/bin along its track for consistent movement
• Helps prevent drawer misalignment, binding, and uneven wear
• Restores secure seating and reduces rattling or shifting during use
• Works as the short/secondary guide where appliances use paired guides

• Disconnect power to the appliance before servicing to avoid shock or injury
• Typical installation requires removing the drawer/bin and fastening the guide with original screws or clips
• Retain and reuse any original hardware unless replacement is explicitly supplied

The R600 Process Valve with Red Cap is an OEM part for GE refrigerators. It regulates the flow of refrigerant within the cooling system, ensuring proper cooling and temperature control.

A bad process valve can occur due to wear and tear, refrigerant leaks, or mechanical failure. If you notice symptoms such as inadequate cooling, excessive frost buildup, or unusual noises coming from the refrigerator, it may indicate a faulty or malfunctioning process valve.

Symptoms of a bad process valve include:

• Inadequate cooling or inconsistent temperature control
• Excessive frost buildup in the freezer
• Unusual noises coming from the refrigerator

Restore your refrigerator by replacing the faulty process valve with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Drier is an OEM component specifically designed for GE combination refrigerator-freezers. Absorbing moisture, its treated silica particles buffer humidity within refrigerant lines. Proper drying sustains energy-efficient performance while preventing corrosion.

Causes of a faulty drier commonly relate to saturation reducing capacity. As desiccant degrades, water passes into closed system compressors requiring change. 

Symptoms of a bad drier involve:

• Frost and ice buildup impairing cooling  
• Puddling around evaporator evidencing leaks
• Higher operating costs from impaired efficiency

Causes of a bad drier involve typical saturation shortening drying cycles. Cracks release desiccant particles risking blockages necessitating timely replacement.

This OEM GE part is also compatible with some Hotpoint, RCA, and Frigidaire combination units. Replace to retain steady humidity management protecting components and maximizing freshness years of operation.
 

This door hinge assembly supports and pivots the refrigerator door to keep it aligned and closing properly. Replacing a worn hinge restores smooth operation and prevents door sag or gaps that can reduce cooling performance. What it does:

• Provides a secure pivot point so the door opens and closes smoothly.
• Keeps door alignment to maintain a consistent seal and reduce air leaks.
• Prevents sagging that can cause rubbing, noise, or uneven wear.
• Common symptom of failure: door hangs, binds, or does not close fully.

• Disconnect power and remove all food and free-standing shelves from the door area before starting.
• Support the door while removing the old hinge to prevent unexpected drops or damage.
• Use appropriate tools and gently tighten fasteners to manufacturer torque; avoid over-tightening.

This wiring harness assembly connects the refrigerator compressor to the electrical system so the compressor receives power and control signals. Replaces a damaged or worn compressor harness to restore reliable electrical connection. What it does:

• Provides the electrical pathway between the compressor and the appliance wiring/controls
• Transmits power and control signals required for compressor operation
• Prevents loose or corroded connections that can cause intermittent compressor function
• Commonly replaced when the compressor won't start, the fridge cycles abnormally, or there is visible wire damage

• Always disconnect power to the appliance before servicing electrical components
• Inspect connectors and routing; replace if terminals are corroded or insulation is cut
• Match connector orientation and secure harness to prevent chafing or contact with hot surfaces

This main electronic control board manages refrigerator functions and user interface, restoring proper timing and power to components for consistent cooling and operation. What it does

• Receives user inputs and runs the refrigerator's control logic for cooling cycles and defrost.
• Sends power and signals to compressor, fans, defrost heater, and lights as needed.
• Can cause unresponsive displays, no cooling cycles, or erratic operation when faulty.
• Helps correct symptoms like blank or flashing control panel, intermittent cooling, or failing defrost cycles.

• Disconnect power to the appliance before servicing to avoid shock.
• Handle the board by the edges and avoid electrostatic discharge; use an ESD strap if available.
• Verify connector orientations and secure mounting screws; do not force connectors.
• After installation, restore power and run a short test cycle to confirm normal operation.

This 120V LED interior light bulb replaces a worn or burned-out refrigerator/freezer light to restore bright, energy-efficient illumination so you can see contents clearly without frequent bulb changes. What it does

• Provides steady, cool-running light for appliance interiors
• Replaces dim, flickering, or non-working interior bulbs
• Uses LED technology for reduced energy use and longer life versus incandescent
• Fits standard appliance interior light fixtures designed for 120V bulbs

• Always disconnect power to the appliance before replacing the bulb to avoid electrical shock.
• Allow the old bulb and surrounding area to cool before handling.
• Install bulb by hand; do not overtighten. Test the light after restoring power.
• If the light still fails after replacing the bulb, check the socket, switch, or wiring.