Parts for Crosley CRT186QW1: Shelves Parts

The Freezer Shelf is an OEM replacement part for  Frigidaire freezers. It is a sturdy and durable wire or glass shelf designed to provide ample storage space within the freezer compartment, allowing you to organize and easily access frozen items. Measuring approximately 24-1/2" W x 12-1/2" D x 5/32" H, the shelf requires no hardware or tools for installation.

Causes of needing to replace a freezer shelf can include physical damage from impact or excessive force, warping or deformation due to temperature fluctuations or moisture over time, or general wear and tear from repeated use.

Symptoms of a bad freezer shelf include:

• Visible cracks or bends in the shelf material
• The shelf becoming loose or unstable, causing items to slide off
• Difficulty sliding the shelf in and out of its designated position

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and warm air out, preserving food freshness and helping the appliance run efficiently. What it does:

• Seals the door to maintain proper internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps reduce compressor runtime caused by air leaks
• Restores a tight magnetic seal for reliable door closure

• Disconnect power before starting any repair.
• Remove the old gasket and clean the gasket channel; install new gasket, aligning the magnetic edge and corners.
• Check for full compression around the door; adjust or reseat as needed for an even seal.
• Allow the gasket to settle and recheck after 24 hours; avoid using sharp tools that could damage the seal.

The Light Switch is an OEM replacement part for Frigidaire refrigerators. This switch controls the interior light of the refrigerator, turning it on when the door is opened and off when the door is closed. It ensures that the refrigerator is properly illuminated, making it easier to find items inside.

Causes of a bad light switch can include electrical malfunctions, physical damage from repeated use, or wear and tear over time.

Symptoms of a bad Light Switch include:

• Interior light not turning on when the door is opened
• Light flickering or intermittently turning on and off
• The refrigerator light staying on even when the door is closed

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Light Bulb (40W) is an OEM part for Frigidaire appliances. Specifically designed to fit and function with Frigidaire models, this 40-watt bulb illuminates the interior of your oven, making it easier to check on the progress of your baking or roasting without opening the oven door.

Over time, oven light bulbs can burn out or be damaged from high temperatures or accidental bumps during cleaning or cooking. A functioning light bulb is crucial for the optimal operation of your oven, enhancing visibility and improving your cooking experience.

Symptoms of a bad Light Bulb include:

• The oven interior remains dark when the light switch is engaged.
• Flickering light, indicating a loose connection or nearing the end of the bulb's lifespan.
• Completely non-functional light, which can hinder your ability to monitor cooking progress.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

The Control Box Assembly is an OEM part for Frigidaire refrigerators. This complete assembly includes the electronic components and housing necessary to manage the refrigerator’s operations, such as temperature regulation, defrost cycles, and other vital functions.  

Causes of a bad control box assembly can include electrical surges, moisture damage, or normal wear and tear over time. Additionally, physical damage or faults in the wiring can lead to control box failure.

Symptoms of a bad control box assembly include:

• The refrigerator not cooling properly
• Error codes displayed on the control panel
• Inconsistent or fluctuating temperatures
• The refrigerator or freezer not defrosting as needed
• Unresponsive control buttons

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This control box housing protects and secures the range/dryer/washer electronic control assembly, keeping wiring and the control board mounted and shielded from debris and heat. It restores a stable enclosure for reliable control operation. What it does:

• Provides a mounting enclosure for the appliance electronic control board and associated wiring harnesses
• Shields circuits from dust, moisture and incidental contact that can cause shorts or intermittent operation
• Keeps control components properly aligned so knobs, switches or displays sit correctly
• Helps prevent vibration-related loosening or damage to the control assembly
• Can eliminate symptoms like loose or rattling controls, exposed wiring, or intermittent control behavior when the housing is broken

• Disconnect power (unplug or turn off breaker) before any service to avoid shock or damage
• Handle the control board and ribbon cables carefully; transfer the PCB and fasteners from the old housing to the new housing if required
• Use the manufacturer-recommended screws/fasteners and correct alignment before restoring power

The Control Box Assembly is an OEM part for Frigidaire refrigerators. This complete assembly includes the electronic components and housing necessary to manage the refrigerator’s operations, such as temperature regulation, defrost cycles, and other vital functions.  

Causes of a bad control box assembly can include electrical surges, moisture damage, or normal wear and tear over time. Additionally, physical damage or faults in the wiring can lead to control box failure.

Symptoms of a bad control box assembly include:

• The refrigerator not cooling properly
• Error codes displayed on the control panel
• Inconsistent or fluctuating temperatures
• The refrigerator or freezer not defrosting as needed
• Unresponsive control buttons

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drawer Cover Frame is an OEM replacement part for Frigidaire refrigerators. This component is specifically designed to house the shelf glass and hold the refrigerator drawer in place.

Causes for a malfunctioning Drawer Cover Frame can include physical damage from overloading, wear and tear from frequent use, or structural issues that affect its ability to securely hold the shelf glass and drawer.

Symptoms of a bad Drawer Cover Frame include:

• The shelf glass not being securely housed, leading to instability
• The refrigerator drawer is not being held firmly, causing misalignment or sliding issues
• Visible cracks or damage to the frame affecting its structural integrity
• Difficulty in accessing or securing the refrigerator drawer due to frame issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Refrigerator Shelf is an OEM part for Frigidaire refrigerators. It is designed to provide a sturdy, flat surface inside the refrigerator compartment, offering a convenient space for storing and organizing food items. This shelf is made from materials that are designed to withstand the typical wear and tear of daily use, as well as the cold temperatures within the fridge.

Causes of a bad Refrigerator Shelf can include cracking due to excess weight, damage from sharp objects, or warping from exposure to extreme temperatures or moisture.

Symptoms of a bad Refrigerator Shelf include:

• Visible cracks or breaks in the shelf,
• Sagging or inability to hold items securely,
• Difficulty sliding the shelf in or out if it is designed to do so.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Crisper Pan Cover is an OEM replacement part for Frigidaire refrigerators. It is a cover component responsible for protecting and enclosing the crisper drawers located in the refrigerator interior. The crisper pan cover works to maintain proper humidity levels inside the crisper, preventing moisture loss and food dehydration. Please note: This cover does not come with the glass

Causes of a bad cover-crisper pan can include cracks or breaks from regular use, damage from heavy items placed on top, or warping due to temperature changes.

Symptoms of a bad crisper pan cover include:

• Excessive drying out of fruits and vegetables stored in the crisper
• Loss of humidity and increased moisture evaporation
• Inability to fully enclose the crisper drawer as designed
• Potential entry points for ethylene gas leaks that accelerate ripening

This OEM Frigidaire replacement part is also compatible with brands like Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replace a cracked or missing produce bin with this refrigerator crisper drawer. It restores proper storage and smooth sliding for fruits and vegetables, helping keep the fresh food section organized and easy to use.

• Holds produce in the fresh food compartment and slides on the crisper rails
• Helps contain spills and keep items separated for better organization
• Replace if cracked, broken, warped, hard to slide, or falling off the track
• Visible damage, missing tabs, or sharp edges are common signs it needs replacement

• Disconnect power to the refrigerator before servicing
• Remove contents; pull the old drawer to the stop, lift/angle to clear rails, and remove
• Align the new drawer with the rails and slide it fully closed
• Reinstall any shelf or cover pieces removed during access

This slide is the track/rail that supports and guides a compatible refrigerator drawer, bin, or basket. Replacing a worn slide restores smooth, even movement so the drawer opens and closes properly without binding or popping off its track.

• Guides and supports a drawer/bin for smooth travel inside the refrigerator
• Common fix for drawers that stick, jam, feel rough, or fall off the track
• Helps keep the drawer aligned and level in its compartment
• Replace if the rail is cracked, warped, or excessively worn

• Disconnect power and remove food/items from the affected area before servicing.
• Remove the drawer and any cover/shelf as needed; retain and reuse existing screws/clips.
• Install the new slide in the same position, then test drawer movement before restoring power.

The MEAT PAN is an OEM part for Frigidaire refrigerators. It is an adjustable pan or bin located within the refrigerator to store raw or cooked meats separately from other foods. The meat pan has raised edges to contain juices and is usually removable for easy cleaning.

Symptoms of a bad meat pan include: 

• Cracks or breaks in the plastic allowing leakage of meat juices 
• Damage or warping preventing proper sealing and fitting within the refrigerator shelf
• Stains or odors from meat or juice residue that cannot be fully cleaned

Causes of a faulty meat pan may be repeated impact or pressure damage over time, exposure to harsh cleaning chemicals, or improper handling resulting in cracks or weakened plastic.

This replacement part is also compatible with KitchenAid, Jenn-Air, and some Kenmore-branded refrigerators.

The Glass Shelf Insert is an OEM replacement part for Frigidaire refrigerators. It provides versatile storage space by allowing items to be viewed clearly and easily rearranged. This insert measures approximately  23.82 x 15.50 inches

Causes of a bad shelf insert may include cracks, chips or other damage due to repeated handling or excessive weight loads not suitable for glass. Normal wear over time can also affect the shelf surface.

Symptoms of issues include: 

• Visible damage detracting from shelf appearance and function
• Increased risk of items stored atop the shelf getting damaged 
• Difficulty cleaning due to cracks or irregular surfaces

This OEM replacement part is compatible with models by Electrolux, Kelvinator and Kenmore as well.

This control box is the molded assembly in the refrigerator compartment that supports the temperature control and air duct components. Replacing a cracked or sagging box helps restore a secure mount and proper airflow routing. What it does

• Mounts the cold control/thermostat and the air diffuser/ducting in the fresh food section
• Helps channel cold air from the freezer into the refrigerator compartment
• Provides attachment points for control knobs and trim
• Typical failure signs: broken tabs, drooping housing, loose control dial, rattling, or obstructed airflow path

• 1 control box

• Disconnect power to the refrigerator before servicing
• Remove shelves/cover to access; take photos to note wiring and component locations
• Transfer existing controls and hardware as needed, then reinstall the housing with original fasteners
• Verify the damper moves freely and controls operate before restoring power

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator shelf spacer positions and supports a shelf so it sits secure and level. Replacing a worn or missing spacer helps eliminate wobble or shifting and restores proper fit and alignment inside the compartment. What it does

• Maintains correct spacing and alignment for the shelf
• Helps keep the shelf level and secure in its track or frame
• Replaces cracked, deformed, or missing spacers
• Symptoms can include a loose, tilted, or rattling shelf, or visible gaps where the shelf should seat

• One shelf spacer

• Disconnect power to the refrigerator before servicing
• Remove the shelf to access the spacer location
• Gently pry out the old spacer; avoid stressing plastic or glass components
• Press the new spacer firmly into place and reinstall the shelf, ensuring proper orientation

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely