Parts for Frigidaire LGHT1846QE4: 04 - Shelves Parts

This replacement frame restores the outer trim around the appliance door for a clean, finished appearance and helps protect internal components from damage. It's a direct-fit exterior trim piece used when the original frame is cracked, bent, or cosmetically worn. What it does:

• Replaces a damaged or bent door/frame trim to restore proper sealing and appearance
• Protects internal edges and components from dents and everyday wear
• Helps maintain a flush fit between the door and appliance cabinet
• Can reduce drafts or light gaps caused by warped or broken trim

• One door/frame trim piece as pictured

• Disconnect power to the appliance before starting any repair
• Installation generally requires removing the door or outer panel and unscrewing fasteners—keep screws organized
• Handle edges carefully to avoid cuts or scratching the finish; use a soft surface to set parts during install

This freezer temperature control assembly regulates cooling by monitoring cabinet temperature and switching the cooling system on and off to match your setting. Replace it if temperatures drift, the unit short-cycles or runs constantly, or the control stops responding. What it does:

• Senses freezer temperature and commands the cooling system to maintain your selected set point
• Provides user adjustment of freezer temperature via the control mechanism
• Helps restore consistent, reliable freezing performance
• Common failure symptoms include too warm or too cold temperatures, continuous running or no run, and an unresponsive temperature dial

• 1 freezer temperature control assembly

• Disconnect power before servicing
• Access the control housing; note wire/harness positions and component orientation for reassembly
• Transfer any reusable mounting parts from the original control as needed; secure wiring away from moving parts
• Set the control to a mid-range setting and allow up to 24 hours for temperatures to stabilize after replacement

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part

This shelf assembly is a replacement glass shelf for refrigerator interiors, restoring stable storage and organized shelving. The tempered glass and frame support food containers and make cleaning simple. What it does

• Replaces a cracked, chipped, or broken refrigerator shelf to restore usable storage space
• Provides a flat, stable surface for storing food containers, plates, and small appliances
• Tempered glass helps resist thermal stress and everyday wear
• Visible trim/frame helps lock the shelf into cabinet tracks and keeps items from sliding

• One shelf assembly (glass shelf with trim/frame), as shown

• Remove power or open door and work carefully to avoid dropping the glass
• Slide shelf into cabinet tracks until it seats; follow your model's shelf-support orientation
• Wear gloves to protect hands when handling broken glass or sharp edges

The Drawer Cover Frame is an OEM replacement part for Frigidaire refrigerators. This component is specifically designed to house the shelf glass and hold the refrigerator drawer in place.

Causes for a malfunctioning Drawer Cover Frame can include physical damage from overloading, wear and tear from frequent use, or structural issues that affect its ability to securely hold the shelf glass and drawer.

Symptoms of a bad Drawer Cover Frame include:

• The shelf glass not being securely housed, leading to instability
• The refrigerator drawer is not being held firmly, causing misalignment or sliding issues
• Visible cracks or damage to the frame affecting its structural integrity
• Difficulty in accessing or securing the refrigerator drawer due to frame issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Crisper Pan Cover is an OEM replacement part for Frigidaire refrigerators. It is a cover component responsible for protecting and enclosing the crisper drawers located in the refrigerator interior. The crisper pan cover works to maintain proper humidity levels inside the crisper, preventing moisture loss and food dehydration. Please note: This cover does not come with the glass

Causes of a bad cover-crisper pan can include cracks or breaks from regular use, damage from heavy items placed on top, or warping due to temperature changes.

Symptoms of a bad crisper pan cover include:

• Excessive drying out of fruits and vegetables stored in the crisper
• Loss of humidity and increased moisture evaporation
• Inability to fully enclose the crisper drawer as designed
• Potential entry points for ethylene gas leaks that accelerate ripening

This OEM Frigidaire replacement part is also compatible with brands like Electrolux, Gibson, Kelvinator, and some Kenmore models.

Replace a cracked or missing produce bin with this refrigerator crisper drawer. It restores proper storage and smooth sliding for fruits and vegetables, helping keep the fresh food section organized and easy to use.

• Holds produce in the fresh food compartment and slides on the crisper rails
• Helps contain spills and keep items separated for better organization
• Replace if cracked, broken, warped, hard to slide, or falling off the track
• Visible damage, missing tabs, or sharp edges are common signs it needs replacement

• Disconnect power to the refrigerator before servicing
• Remove contents; pull the old drawer to the stop, lift/angle to clear rails, and remove
• Align the new drawer with the rails and slide it fully closed
• Reinstall any shelf or cover pieces removed during access

A replacement shelf trim that restores the front retainer and appearance of a refrigerator door shelf. Replaces cracked, broken, or missing trim to help keep items secure and improve the fridge's look. What it does:

• Secures items on the door shelf by forming the front retainer edge.
• Restores a finished appearance when the original trim is cracked, chipped, or faded.
• Helps prevent small items from sliding forward and falling off the shelf.
• Matches OEM fit and snaps into the existing shelf rail for a clean replacement.

• Empty and remove the door shelf or move items off the shelf before replacing the trim.
• Trim typically snaps into place; gently pry out the old trim and snap the new trim onto the shelf rail.
• No special tools are usually required; use a plastic trim tool to avoid scratching.

The MEAT PAN is an OEM part for Frigidaire refrigerators. It is an adjustable pan or bin located within the refrigerator to store raw or cooked meats separately from other foods. The meat pan has raised edges to contain juices and is usually removable for easy cleaning.

Symptoms of a bad meat pan include: 

• Cracks or breaks in the plastic allowing leakage of meat juices 
• Damage or warping preventing proper sealing and fitting within the refrigerator shelf
• Stains or odors from meat or juice residue that cannot be fully cleaned

Causes of a faulty meat pan may be repeated impact or pressure damage over time, exposure to harsh cleaning chemicals, or improper handling resulting in cracks or weakened plastic.

This replacement part is also compatible with KitchenAid, Jenn-Air, and some Kenmore-branded refrigerators.

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

The Glass Shelf Insert is an OEM replacement part for Frigidaire refrigerators. It provides versatile storage space by allowing items to be viewed clearly and easily rearranged. This insert measures approximately  23.82 x 15.50 inches

Causes of a bad shelf insert may include cracks, chips or other damage due to repeated handling or excessive weight loads not suitable for glass. Normal wear over time can also affect the shelf surface.

Symptoms of issues include: 

• Visible damage detracting from shelf appearance and function
• Increased risk of items stored atop the shelf getting damaged 
• Difficulty cleaning due to cracks or irregular surfaces

This OEM replacement part is compatible with models by Electrolux, Kelvinator and Kenmore as well.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This shelf spacer is a genuine OEM replacement part sourced directly from the manufacturer, and it is used in refrigerators and freezers. This shelf spacer attaches to wire shelves in the refrigerator and freezer to hold them in place. If the shelf spacer is lost or damaged, the shelf will not stay in place. The spacer should be replaced.Refrigerator shelves must be sturdy to hold the weight of the food stored inside. If the shelf spacer is missing, the stability of the shelf is compromised. This part snaps onto the wire shelf and prevents it from moving around. This keeps the food inside the refrigerator from causing the shelf to fall. No tools are needed to install this part. If the shelf spacer is missing, do not store food on the shelf until it is installed.This shelf spacer is a white plastic part that is sold individually. It is designed for use in refrigerators manufactured by Kenmore, Frigidaire, Westinghouse, and Gibson.