Parts for Frigidaire LGHT2046QE1: 04 - Shelves Parts

This freezer temperature control assembly regulates cooling by monitoring cabinet temperature and switching the cooling system on and off to match your setting. Replace it if temperatures drift, the unit short-cycles or runs constantly, or the control stops responding. What it does:

• Senses freezer temperature and commands the cooling system to maintain your selected set point
• Provides user adjustment of freezer temperature via the control mechanism
• Helps restore consistent, reliable freezing performance
• Common failure symptoms include too warm or too cold temperatures, continuous running or no run, and an unresponsive temperature dial

• 1 freezer temperature control assembly

• Disconnect power before servicing
• Access the control housing; note wire/harness positions and component orientation for reassembly
• Transfer any reusable mounting parts from the original control as needed; secure wiring away from moving parts
• Set the control to a mid-range setting and allow up to 24 hours for temperatures to stabilize after replacement

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part

This model-specific refrigerator cover encloses and protects a designated interior area or component. Replacing a cracked, loose, or missing cover restores proper fit and finish and helps maintain intended airflow and safe operation inside the cabinet. What it does

• Shields and encloses the specified compartment to protect internal components from debris and damage
• Helps maintain designed airflow and temperature by properly closing the opening
• Restores a clean, finished look and prevents items from snagging or falling into moving parts
• Common symptoms: cracked or broken cover, loose fit or rattling, visible gaps, or the cover will not stay attached

• 1 cover

• Disconnect power and remove items, shelves, or bins as needed to access the area
• Note fastener type and locations; retain and reuse original hardware
• Align tabs/guides, seat the cover fully, then secure without overtightening
• Restore power and confirm the cover is secure and clear of any fan or moving parts

The Crisper Pan Cover is an OEM part for Frigidaire refrigerators. It serves as the shelf that sits above the crisper drawers and supports various items while providing a lid to help maintain the humidity levels necessary to keep fruits and vegetables fresh longer. This cover typically is only the frame and does not include the glass.

Symptoms of a bad Crisper Pan Cover include:

• Cracks or damage to the cover that can compromise its structural integrity
• Warping or bending that affects the fit and function
• Difficulty sliding or fitting the cover properly over the crisper drawers

Causes of a bad crisper pan cover can include overloading the shelf with too much weight, impacts from dropping heavy items, or thermal stress from fluctuations in refrigerator temperatures.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This refrigerator drawer pan replaces a broken or missing bin in the fresh food section. Restore organized storage and smooth sliding access so produce and snacks stay contained and easy to reach.

• Holds and organizes items in the refrigerator's fresh food compartment
• Helps contain drips and spills to keep shelves cleaner
• Slides on existing tracks for easy access
• Replace when cracked, warped, or the front/lip is broken, or the drawer sticks, falls, or is missing

• Remove contents; pull the old drawer straight out to clear the tracks or stops
• Align the new pan with the same tracks and slide it in until fully seated
• Do not force into place; handle carefully to avoid cracking

This slide is the track/rail that supports and guides a compatible refrigerator drawer, bin, or basket. Replacing a worn slide restores smooth, even movement so the drawer opens and closes properly without binding or popping off its track.

• Guides and supports a drawer/bin for smooth travel inside the refrigerator
• Common fix for drawers that stick, jam, feel rough, or fall off the track
• Helps keep the drawer aligned and level in its compartment
• Replace if the rail is cracked, warped, or excessively worn

• Disconnect power and remove food/items from the affected area before servicing.
• Remove the drawer and any cover/shelf as needed; retain and reuse existing screws/clips.
• Install the new slide in the same position, then test drawer movement before restoring power.

A replacement shelf trim that restores the front retainer and appearance of a refrigerator door shelf. Replaces cracked, broken, or missing trim to help keep items secure and improve the fridge's look. What it does:

• Secures items on the door shelf by forming the front retainer edge.
• Restores a finished appearance when the original trim is cracked, chipped, or faded.
• Helps prevent small items from sliding forward and falling off the shelf.
• Matches OEM fit and snaps into the existing shelf rail for a clean replacement.

• Empty and remove the door shelf or move items off the shelf before replacing the trim.
• Trim typically snaps into place; gently pry out the old trim and snap the new trim onto the shelf rail.
• No special tools are usually required; use a plastic trim tool to avoid scratching.

This meat pan is the replacement deli-style tray used inside the refrigerator to hold meats, cheeses and other deli items. It restores proper storage and organization for the deli/drawer area. What it does:

• Provides a flat, food-safe surface for storing deli meats, cheeses and prepared foods
• Keeps items contained to reduce spills and cross-contamination inside the deli/drawer area
• Replaces a cracked, warped or missing deli/meat tray to restore usable storage
• Fits into the fridge's deli/drawer track or shelf area to align with the existing drawer

• One meat pan/deli tray (single replacement)

• Remove food items and the deli drawer before installing the new pan
• Slide the pan into the existing drawer tracks or set it into the shelf support as originally positioned
• Hand-wash with mild detergent; avoid abrasive cleaners or scouring pads that can damage the surface

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

The Pan Cover Glass Insert is an OEM part for Frigidaire refrigerators. It acts as the shelf above the crisper drawers, providing a stable and transparent surface for storing fruits, vegetables, and other perishables. This glass insert is crucial for maintaining the organization within the fridge, allowing for easy visibility and access to items stored in the crisper drawers beneath it. 

Causes of damage to the Pan Cover Glass Insert can include overloading it with too heavy items, accidental impacts during the loading or unloading of groceries, or sudden temperature changes that can cause glass to weaken or crack.

Symptoms indicating the need for a replacement include:

• Visible cracks or chips in the glass
• Scratches that impair visibility
• Shattering of the glass insert

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This shelf spacer is a genuine OEM replacement part sourced directly from the manufacturer, and it is used in refrigerators and freezers. This shelf spacer attaches to wire shelves in the refrigerator and freezer to hold them in place. If the shelf spacer is lost or damaged, the shelf will not stay in place. The spacer should be replaced.Refrigerator shelves must be sturdy to hold the weight of the food stored inside. If the shelf spacer is missing, the stability of the shelf is compromised. This part snaps onto the wire shelf and prevents it from moving around. This keeps the food inside the refrigerator from causing the shelf to fall. No tools are needed to install this part. If the shelf spacer is missing, do not store food on the shelf until it is installed.This shelf spacer is a white plastic part that is sold individually. It is designed for use in refrigerators manufactured by Kenmore, Frigidaire, Westinghouse, and Gibson.

This support beam is the structural rail that supports a refrigerator shelf and its pantry/drawer assembly. Replace a cracked or missing beam to restore level support, prevent sagging, and keep drawers operating smoothly.

• Spans the compartment to support the shelf/pantry frame and distribute weight
• Keeps the shelf level and stable under load
• Helps maintain proper alignment for attached drawers or bins
• Common symptoms: shelf tilts or sags; drawers bind, scrape, or drop
• Visible cracks, broken tabs, or a missing beam

• Disconnect power before servicing
• Remove food items, the shelf/frame, and any drawers or bins supported by the beam
• Release the beam from locking tabs or fasteners and remove the old part
• Seat the new beam fully in the mounting points, then reinstall the shelf and drawers and check for level

This small clip secures the crisper cover's slide so it stays aligned and operates smoothly. Replacing a broken or missing clip restores proper slide action and helps keep your crisper cover assembly functioning as designed.

• Holds the crisper cover slide in place and aligned with its track
• Helps the slide move smoothly without popping off or binding
• Common symptoms: slide is loose or falls out, won't stay in place, cracked/missing clip
• Visual damage or loss can leave the crisper drawer cover slide inoperable

• Disconnect power and remove food items for safe access
• Remove the crisper drawer and lift out the crisper cover assembly
• Release the damaged clip and snap the new clip into the cover/slide as oriented
• Reassemble and verify the slide moves freely end to end