Parts for Frigidaire FPCE24VWPW2: 05 - Shelves And Supports Parts

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

1/4"diameter - 93" long, plastic, cut-to fit

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This part has been discontinued by the manufacturer and is no longer available.

A left-side support bracket that secures and stabilizes the appliance component it mounts to, restoring proper alignment and load-bearing function for safe, reliable operation. What it does

• Replaces a cracked, broken or worn left support bracket that allows the component to sag or sit unevenly.
• Restores proper alignment so drawers, shelves or panels move smoothly and sit level.
• Helps prevent additional wear or damage caused by a loose or failing support.
• Fits in the left-side mounting position as the OEM replacement part.

• Disconnect power and/or unplug the appliance before beginning any repair.
• Basic hand tools are typically required; handle edges carefully to avoid injury.
• Keep removed fasteners and any small parts for reassembly; compare new part to the old before installing.

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear where wiring, rods or panels pass through mounting openings. It helps keep parts aligned and protects against chafing and noise. What it does:

• Cushions and isolates vibration between moving parts and chassis
• Protects wiring, tubes or rods from rubbing and abrasion at mounting holes
• Helps reduce noise caused by contact or metal-on-metal vibration
• Aids in maintaining proper part alignment and secure fit

• Grommet

• Inspect mating hole and surrounding area for debris or sharp edges before installing
• Fit the grommet into the mounting hole so the flange seats evenly on both sides
• Replace any damaged or excessively worn grommets to restore protection
• Disconnect power and follow appliance safety procedures before attempting service

This screw fastener secures appliance panels and small components to restore proper fit and reduce vibration. It's a direct-replacement OEM-style fastener used where factory screws are required. What it does:

• Secures trim, panels, or brackets to prevent rattling and misalignment
• Replaces missing or damaged screws that allow parts to shift or vibrate
• Restores stable mounting for controls, housings, and interior components
• Helps maintain proper gaps and seals when fastening exterior or interior pieces

• One screw fastener

• Unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Install by hand initially, then snug—do not overtighten to avoid damaging threads or parts
• If original screw is corroded or broken, compare head type and length to ensure correct fit

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required