Search Results

Washer won't fill properly or overfills? This water level pressure switch senses fill levels and signals when to stop. Easy DIY fix for cycle timing issues.

If your electric range burner won't heat properly or won't turn off, this infinite switch controls power to the surface element. Moderate DIY repair.

Restore dependable control with this replacement switch. It replaces a worn or unresponsive control so your unit responds consistently when operated, helping eliminate intermittent operation and no-response issues caused by fatigued contacts or mechanical wear. What it does

• Controls electrical power to the selected function within the unit
• Can resolve symptoms like no response, intermittent operation, or a switch that sticks or feels loose
• Installs in the original control location for a straightforward replacement

• 1 switch

• Disconnect power at the breaker before servicing
• Access the control area and note wire locations or take a clear photo
• Move wires one at a time to the new switch; ensure spade terminals are fully seated
• Test operation before reassembling covers or panels

Burner stuck on high or won't heat? The infinite switch controls surface element power from low to high. Common DIY fix restores heat adjustment.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

This replacement capacitor stores and releases electrical energy to support proper operation of the appliance's circuit. Replacing a weakened or failed capacitor restores reliable startup and smooth performance in the affected component.

• Stores electrical energy and delivers a brief boost during startup as designed by the circuit
• Helps stabilize operation, reducing humming, stalling, or overheating from a weak capacitor
• Common signs include motors that hum but won't start, intermittent operation, breaker trips
• Visual clues of failure: swollen case, leaking oil, or burnt odor

• Disconnect power and verify no voltage is present before servicing
• Properly discharge the old capacitor using safe, approved procedures
• Note wire positions or take a photo; transfer leads to the matching terminals securely
• Mount securely in the existing bracket/strap; keep terminals clear of contact and test operation

Fixes continuous clicking or burners that won't spark when you turn the knob. This harness connects knob switches to the ignition circuit. DIY-friendly repair.

This plunger switch is the push-style electrical switch that completes a circuit when an actuator is depressed, restoring reliable on/off signaling. Use it to replace a worn or broken plunger switch that causes intermittent or non-responsive operation. What it does:

• Closes an electrical circuit when the plunger is pushed, sending a signal to the appliance control.
• Commonly used where a door, lever or dispenser actuator must register a position or user input.
• Can correct symptoms like intermittent operation, a dispenser or mechanism that won't activate, or a stuck/unresponsive actuator.
• Acts as a direct mechanical-to-electrical interface—no electronics required.

• Disconnect power (unplug or turn off breaker) before servicing to avoid shock.
• Remove the access panel or housing to reach the switch; note actuator orientation before removal.
• Disconnect terminals or harness, then swap the old switch for the new one; reconnect terminals securely.
• Test the plunger action and appliance function before reinstalling panels.

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

Fix a dishwasher with no control panel lights or one that won't start cycles. This switch assembly restores electrical signals for reliable operation.

Burner won't heat or stays on constantly? This range burner control switch regulates cooktop element temperature. Straightforward DIY fix.

Burner stuck on high or dual element not working? This infinite switch controls heat levels. Moderate DIY; transfer wires one at a time carefully.

Fix a burner stuck on high or not heating with this surface element switch. Controls power to your cooktop heating element. DIY-friendly repair.

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.

The Infinite Switch is an OEM part for GE electric ranges. It regulates precise temperature settings for the bake and surface elements.  This is specifically for 6" inch elements.

Symptoms of a bad infinite switch include:

• Wide variations in cooking temperatures 
• Failure to attain or maintain desired heat levels
• Non-working or faulty temperature selector dial 

Causes can involve degraded metal contacts, worn internal components, or damaged wiring connections after extended use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore electric range models. 

Fix a washer that won't advance cycles or gets stuck between rinse and spin. This cycle selector switch controls washing cycle progression.