Tecumseh Engine Carburetor

This is a replacement for a carburetor in lawn and garden equipment engines. The carburetor is responsible for creating the air and fuel mixture that goes into the engine to create the combustion and start the machine. It contains several parts and can become worn, damaged, or even just clogged over time. In many cases, it's more affordable and easier to replace or repair a carburetor than it is to replace the entire unit. Be sure to use an OEM part like this to do the job. To replace the carburetor, simply allow the engine to cool and then remove the old one from the engine. Then, replace the new unit, screw it into place, and connect the fuel lines. Test it by pouring fuel straight into the carb and starting the engine. If it fires and wants to stay running, the problem is solved. This OEM carburetor replacement is compatible with several models of 4-cycle engines from Tecumseh. It comes as an entire assembly and is sold as an individual unit. Other parts and hardware will require an additional purchase.

This carburetor repair kit is made to be used with several types of lawn and garden equipment with small engines. It has all the replacement parts needed to get a generator or snowblower running again if there is a problem with the carburetor. The carburetor is a component inside the lawn equipment that controls the mixture of air and fuel that ignites within a cylinder to cause the engine to run.If the lawn and garden equipment refuses to start up even with a full tank of fuel, this is one of the primary signs that the carburetor has gone bad and will need repairs or replacement. Remove the air filter and pour a small amount of fuel into the carburetor to test where the component is working the way it should be. If the engine turns on but then dies after a short period of time, there is likely an issue with the carburetor. It will need to be rebuilt or replaced.This is a genuine OEM replacement carburetor repair kit directly sourced from the manufacturer. It is compatible with snowblowers and generators manufactured by Craftsman, Tecumseh, Cub Cadet, Toro, and Husqvarna. Each repair kit is sold individually and may require basic tools for installation.

This is a throttle link made to be used by many types of lawn and garden equipment. It is a metal part that connects the carburetor to the throttle controls. If the throttle link is damaged or broken, it will not be possible to change the speed of the tool's engine. In some cases, if the throttle link is malfunctioning or broken, the equipment may not run at all.The throttle link is made of durable materials but it can be weakened by continued use due to stress and vibrations. This can cause the link to break down and stop working. If this occurs, it will need to be replaced. A screwdriver or an Allen wrench will be required to handle the replacement process. The throttle link will need to be removed from the throttle body so the replacement part can be installed.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The throttle link is created for use with snowblowers, lawnmowers, tillers, pressure washers, and generators made by Briggs & Stratton, Tecumseh, Cub Cadet, Craftsman, MTD, Simplicity, and Toro.

The carburetor repair kit provides buyers with several replacement parts that can be used to repair carburetors on various types of lawn and garden equipment. The carburetor is the location where the fuel and air mix for the internal combustion of the engine, and it needs to be in good working order. However, the carburetor may have issues that will need to be repaired, such as corroded springs or lost welch plugs. Whether through natural wear and tear, outside damage, or being lost, it is important for owners to ensure their carburetor is repaired as soon as possible. A bad carburetor can make it difficult to start the engine, cause misfires, and reduce power. This repair kit provides genuine OEM parts for carburetors. The kit includes commonly replaced parts including needles, welch plugs, screws, O-rings, and springs. The parts are used for carburetors on equipment such as snowblowers, generators, lawn mowers, and other small engines. They are compatible with Toro, Tecumseh, Briggs & Stratton, and Craftsman machines. Buyers should always consult their manual to be sure they are choosing the correct replacement parts for their make and model.

The comprehensive carburetor kit contains all of the parts and components necessary to make almost any repair to a carburetor on the makes and models mentioned. A carburetor is a part that mixes air and fuel within any combustion engine. Without adequate or ideal air to fuel mixtures, the engine may misfire or run poorly. It is not unusual for older or heavily used engines to need carburetor repairs. This is a carburetor kit for lawn tractors, lawnmowers, and small engines made by Tecumseh, Toro, Lawn-Boy, Cub Cadet, and MTD, among others. It ships individually.

This carburetor nzle fits lawnmowers, lawn tractors, tillers, and other lawn and garden equipment. It is the part of the carburetor assembly that guides the fuel inside of the carburetor and maintains the proper fuel to air ratio. This is an essential part of engine performance. If the carburetor nzle is clogged, damaged, or broken, the engine will not run properly. The carburetor nzle can be replaced as a single repair or as part of an overall carburetor rebuild. Remove the carburetor float and float ring to get to the bowl. Remove the carburetor nzle from inside the carburetor throat with long nose pliers or by pressing it out manually. Ensure both o-rings come out with the nzle; if not, fish them out of the carburetor bowl. Install the o-rings on the new carburetor nzle before installation. This repair should be done in an area with adequate ventilation. Be sure to drain the fuel tank before removing the carburetor and take the spark plug off the engine.This carburetor nzle is sold as an individual unit. It is designed for lawn and garden equipment engines manufactured by Craftsman, Tecumseh, Cub Cadet, Lawn-Boy, and Toro.

The main nozzle is a part of the carburetor in pressure washers and snowblowers. This is a part of the carburetor assembly and it can be located between the carburetor bowl and carburetor body. It passes through the plastic float component. The nzle is used to direct air or water in the right direction when using the lawn and garden equipment. The main nzle can experience wear and tear or damage which will make it incapable of blowing air or water.If the nzle is broken or cracked, it needs to be replaced. A set of basic tools and work gloves will be useful during the process. First, the carburetor will need to be removed from the equipment. Disassemble the carburetor to gain access to the main nzle. Take the original component out and replace it with a new part. Make sure to reassemble all components before use.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The main nzle is designed for use in the carburetor of snowblowers and pressure washers manufactured by Lawn-Boy, Briggs & Stratton, Toro, and Tecumseh.

A primer bulb works to lubricate the engine with oil by pressing in the rounded tip of the primer bulb. It measures an inch in diameter and an inch tall. Over time these parts can wear out from sun exposure, contact with chemicals, or dry rot. The gasket may wear out before the primer bulb, so it is important to check this part regularly to discover any damage. Installing the new primer bulb kit should be easy and only take a few minutes. Only a screwdriver set and pliers are needed to complete this repair. This primer bulb kit works in conjunction with small engines, lawnmowers, log splitters, and pressure washers made by brands Briggs & Stratton, Craftsman, Cub Cadet, Lawn-Boy, MTD, Tecumseh, and Toro. It is a genuine OEM part and is sold individually.

The primary function of a carburetor is to mix fuel and air in the right ratio. Fuel enters the carburetor through the fuel inlet fitting and then to the float bowl which delivers fuel to the other circuits. From there, the fuel goes to the needle valve, which is actuated by the float. When there is insufficient fuel, the float will stay down, keeping the valve open. Once the chamber has enough fuel, the float will go up and close the valve. A failed float bowl may leak or have too many dirt particles deposits that impede fuel flow. Luckily, you can easily replace a busted float bowl. This part is a genuine OEM Tecumseh 631867 float bowl replacement. You’ll have the assurance that this replacement is manufactured according to Tecumseh’s highest standards. It is compatible with mowers, tractors, and snowblowers from Toro, Cub Cadet, Lawn-Boy, MTD, and Tecumseh. This part is sold individually.

This is a carburetor bowl. It holds the gas that is mixed with air before it enters the engine. The carburetor bowl contains a float which regulates the amount of gas needed to mix and fuel the engine.There are times when the carburetor in of itself is considered in good working order but the bowl may be compromised. This can happen if the bowl has been corroded. Rust will damage the carburetor bowl and render it ineffective. When replacing the carburetor bowl, be sure to work in a well-ventilated area and to wear the proper gear when handling engine parts. Once the carburetor is free from the engine, unscrew the bowl from the unit over a catch pan. Any contents will fall into the pan. Disassemble the old bowl's hardware and use it when installing the new bowl.This is a genuine OEM part manufactured by Tecumseh. It is compatible for Toro, Cub Cadet, and MTD engines.

This part is an inlet needle. This inlet needle works like a valve to transport fuel into the carburetor bowl when the bowl has drained and then stops fuel intake when the carburetor bowl is full. A new inlet needle may be needed if the fuel is not flowing into the bowl as it is supposed to. This can be evident if the carburetor floods or if the engine does not have enough fuel when it's operating at high speeds. A visual inspection of the inlet needle can also be a good indicator of whether or not it needs to be replaced. If any physical signs of damage are present, the inlet needle will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine Tecumseh part and is an OEM part sourced directly from the manufacturer and it is sold individually. This inlet needle is compatible with snowblowers manufactured by Tecumseh and Toro.

The float shaft and pin are a genuine replacement for select Tecumseh carburetors on small lawn and garden equipment engines. The float shaft and pin are responsible for maintaining the fuel level within the carburetor. Over time because of repetitive motion, the float pin and shaft can break or become damaged, which will stop the carburetor from functioning properly. If the carburetor cannot function, the engine will not be able to perform. If left unattended, the engine and carburetor could fail completely or bigger issues could occur. Replacing the float is essential to getting the equipment back in order. This genuine float shaft and pin is designed for use on machines from Tecumseh, Poulan, Husqvarna, Lawn Boy, Cub Cadet, MTD, and Craftsman, and is compatible with a number of models. The fuel system should be drained and the engine should be cool before any engine repairs are started. Always wear gloves for hand protection. This float shaft and pin are made of durable materials and sold as a unit. No additional hardware or parts are included.

This is a replacement carburetor used with a wide variety of lawn and garden equipment. It includes the full assembly for the carburetor and is responsible for mixing air and fuel together before both are transferred to the engine's combustion chamber. If the carburetor is damaged, the engine may not start as expected, even when the fuel tank is full. Carburetors can also become clogged by dirt or other debris.If the engine is not starting as expected and there is plenty of fuel in the tank, the best thing to do is test the carburetor for problems. This involves adding around a teaspoon of fuel to the carburetor itself after removing the air filter. If the carburetor is the problem, the engine should start but will quickly shut off. A socket set, pliers, and a screwdriver will be needed to replace the part.This carburetor is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual product. The carburetor is designed to fit generators and wood chippers created by Briggs & Stratton, Craftsman, Simplicity, and Tecumseh.