Parts for Kenmore 110.C67032601 (110C67032601, 110 C67032601): Top And Console Parts

This control knob replaces a worn or broken range/oven front knob to restore tactile control and clear temperature/setting selection. It gives a secure fit so you can safely set burners or oven functions. What it does:

• Replaces a damaged or missing control knob to restore manual control of burners or oven settings
• Provides a clear pointer for accurate selection of heat levels and functions
• Snaps on to the stove/range control shaft for reliable operation
• Helps eliminate slipping, stripped splines, or loose turning caused by a worn knob

• One control knob as shown

• Turn power and gas supply off before servicing; follow appliance safety guidance
• Pull off the old knob straight from the control shaft and push the replacement fully onto the shaft until it seats
• If knob does not fit, do not hammer or modify the shaft

This replacement dryer control board is made by Whirlpool. The control board manages the various different functions of the appliance, such as the temperature and drying time. As the appliance ages or is used regularly, this part may begin to grow faulty, causing the user to be unable to use the dryer as intended. If the error code F-01 is visible on the display or the display fails to light up despite being connected to power, it's an indication the control board needs to be replaced. Wear work gloves for safety whenever replacing or repairing any parts. This is a genuine OEM part and has been sourced directly from the manufacturer. This is an authentic part made of high-quality, durable materials and is sold individually. This control board can be used with various different models of dryers that have been manufactured Whirlpool, Maytag, Jenn-Air, Amana, and some other brands.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

Screw for control panel.

This harness clip secures appliance wiring to the cabinet or components to prevent rubbing, pinching, and interference with moving parts. It keeps wiring routed neatly for reliable operation and reduced risk of abrasion-related failures. What it does:

• Holds wire harnesses in place to prevent chafing against sharp edges or moving parts
• Reduces vibration-related noise and intermittent connections caused by loose wiring
• Helps maintain proper wire routing around panels, motors, and heaters
• Supports safe operation by keeping wires away from heat sources and pinch points

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove panels or access covers as needed to reach the original clip location
• Install by snapping or seating the clip into the original mounting point and securing the harness in the retainer; replace any broken mounts
• Inspect surrounding wiring and replace damaged wires or insulation before completing repair

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

For mating terminal use [AP31136300].

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it