Parts for Whirlpool 7MWGD8620HC1: Top And Console Parts

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This bracket is a small mounting support that secures appliance panels or components in place to restore stable alignment and reduce rattling. It's a direct-fit replacement that helps keep parts properly positioned for reliable operation. What it does:

• Provides a secure mounting point for a panel or internal component to prevent shifting or vibration
• Restores correct alignment for doors, panels, or assemblies that have become loose
• Helps eliminate rattling, buzzing, or scraping noises caused by a loose support
• Maintains proper spacing so attached components operate smoothly

• Verify appliance is unplugged or power is disconnected before starting work
• Inspect mounting area and fasteners; replace any damaged screws or clips as needed
• Use basic hand tools to remove and reinstall the bracket; avoid overtightening

This wire harness routes power and signals between the appliance's controls and components, restoring proper electrical connections for reliable operation. Replace a damaged or burned harness to fix intermittent or lost power and unresponsive controls. What it does

• Connects control board, switches and sensors so components receive power and signals
• Replaces frayed, melted or damaged wiring that can cause intermittent faults
• Helps resolve symptoms like controls not responding, lights or motors failing to start, or erratic operation
• Maintains correct wire routing and connector fit to prevent electrical shorts

• Disconnect power and, for gas models, turn off gas supply before starting any repair
• Handle connectors carefully; match connector shapes and pin count when reinstalling
• Route the harness along original clips and channels to avoid heat or pinch points

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Console is an OEM component specifically designed for Whirlpool electric dryers. Located at the top front of the dryer, it houses all controls and programming functions.

Causes of a faulty console include cracks developing from repeated opening and closing of the dryer door over many cycles. Heat exposure and general wear can also degrade plastic surfaces. 

Symptoms of a bad console include:

• Misaligned or loose attachment to the dryer cabinet
• Warm air leaking from openings around control edges
• Buttons sticking or controls ceasing to respond properly
• Visible cracks or broken-off segments 

This OEM Whirlpool replacement console ensures a tight fit and proper seal. Installed promptly, it prevents compromised ventilation and continued component connection damage.

Compatible also with some GE and Crosley models, this part restores seamless operation. Protect your trusted dryer with an OEM console replacement to maintain performance.

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.

This wire harness is a direct-replacement electrical wiring assembly that connects controls, switches and motors so your appliance can send power and signals where needed. It restores proper electrical pathways and helps components operate reliably. What it does:

• Routes and connects electrical power between controls, switches and motors
• Transfers control signals to start or stop appliance functions
• Replaces damaged or frayed wiring that can cause intermittent operation
• Commonly used when an appliance won't start, has intermittent power, or certain controls stop responding

• Disconnect all power before servicing to avoid shock or injury
• Verify connector alignment and seating; match wire colors and connector shapes
• Route and secure wiring away from moving parts, sharp edges and heat sources
• Replace the harness—do not splice unless explicitly approved by the manufacturer