Parts for DEGX1-96010B: Top Deck And Electronics Parts

This is a stainless steel #8 x 5/8" Phillips screw sold in a pack of 10 — a direct-fit fastener for appliance panels, brackets, and trim. Durable corrosion resistance helps maintain secure assemblies over time. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components using a Phillips driver
• Stainless finish resists rust and corrosion in humid or wet appliance areas
• Sized for common appliance mounting points where #8 x 5/8" screws are specified
• Helps restore loose or missing fasteners that cause rattling or poorly seated panels

• Ten (10) stainless steel #8 x 5/8" Phillips screws

• Use the correct #2 Phillips bit and moderate torque to avoid stripping the head or damaging mating parts
• Tighten until snug; do not overtighten plastic components
• Disconnect power to the appliance before accessing internal panels or wiring
• Keep loose screws away from children and dispose of packaging responsibly

This control panel DX1 is the front user interface for the appliance, giving you the buttons and display needed to select cycles and settings. It restores normal control access and visible status feedback. What it does:

• Provides the push-button controls and display used to start and adjust cycles
• Relays user commands to the appliance's control system for cycle selection
• Commonly replaced for unresponsive buttons, missing/blank display segments, or incorrect control behavior
• Helps restore reliable user input and visible status indicators

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle the panel carefully to avoid damaging the display, ribbon cables, or connectors
• Use basic hand tools;
• Verify connector seating and cable routing before reassembly and power-up

This display kit replaces a failed dryer control display so you can see and select drying cycles and settings. It restores visible status feedback and allows normal control-panel operation for troubleshooting or repair. What it does:

• Replaces the dryer's front control/display assembly to restore on-screen indicators and control input response
• Makes cycle status, temperature, and timer information readable again
• Helps resolve symptoms such as blank or non-responsive display, missing indicators, or unreadable characters
• Works with the existing control harness and front console so normal button presses register correctly

• Disconnect power before servicing to avoid electrical shock and damage
• Remove the dryer top or front panel per service manual to access the display assembly
• Handle the display carefully to avoid scratching or bending the panel and ribbon connectors

The Lid Assembly is an OEM part for Fisher & Paykel dryers. It consists of the dryer lid and attached hinges, which provide controlled access to the drying chamber.

Symptoms of a bad lid assembly include:

• Difficulty opening or closing the dryer lid
• Loose, unstable, or off-track movement of the lid
• Gaps in the lid seal letting heated air escape

Causes of failure can be stripped or worn-out hinges, broken seals or cracked plastic over prolonged use. Overloading the dryer can also put excess stress on the lid assembly.

The Safety Thermostat is an OEM part for Fisher & Paykel dryers. As an important safety device, the thermostat monitors the dryer drum temperature and automatically shuts off the dryer if temperatures become excessively high. It plays a protective role by preventing overheating that could pose a fire hazard.

Causes can be normal wear and tear over extended use.  
Symptoms of a bad safety thermostat include:

• The dryer failing to heat or heating unevenly
• Abnormal drying times as heat is improperly regulated
• Shut offs mid-cycle accompanied by flashing lights or error codes

The Thermostat Auto Reset is an OEM replacement part for Fisher & Paykel electric and gas dryers. Precisely located within heating circuits, it monitors internal air temperatures and automatically resets the thermostat when needed. 

Causes of a faulty reset thermostat can include:  

• Fluctuating or inconsistent vent temperatures   
• Frequent on-off cycling of gas valves or heating coils
• Triggering of drying error codes and safety shutoffs
• Inability to detect correct drying time end points

Symptoms involve temperature swings, premature shutoffs, and unfinished loads. Long term exposure to heat or combustion byproducts can degrade sensor function over time. 

This replacement lid use & care label provides the appliance's original on-lid instructions and safety reminders to help you operate and maintain your appliance correctly. Durable adhesive design keeps instructions visible where needed. What it does

• Replaces worn or missing on-lid instruction and care information
• Restores visible safety warnings and basic operating guidance
• Helps users follow recommended care to avoid damage or misuse
• Keeps important reminders in the location intended by the manufacturer

• Clean and dry the lid surface thoroughly before applying
• Peel backing and align label; press firmly from center outward to remove air bubbles
• Do not apply over wet or greasy surfaces; avoid repositioning after initial contact
• Dispose of old adhesive residue; follow appliance safety precautions when working around the lid