Parts for GWL15-96155A: Top Deck & Electronics Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This is a stainless steel #8 x 5/8" Phillips screw sold in a pack of 10 — a direct-fit fastener for appliance panels, brackets, and trim. Durable corrosion resistance helps maintain secure assemblies over time. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components using a Phillips driver
• Stainless finish resists rust and corrosion in humid or wet appliance areas
• Sized for common appliance mounting points where #8 x 5/8" screws are specified
• Helps restore loose or missing fasteners that cause rattling or poorly seated panels

• Ten (10) stainless steel #8 x 5/8" Phillips screws

• Use the correct #2 Phillips bit and moderate torque to avoid stripping the head or damaging mating parts
• Tighten until snug; do not overtighten plastic components
• Disconnect power to the appliance before accessing internal panels or wiring
• Keep loose screws away from children and dispose of packaging responsibly

This is a replacement clip designed to secure the dual inlet valve fittings on compatible washers and dishwashers, helping keep inlet hoses and valve connections firmly in place and reduce the risk of disconnection. What it does:

• Holds dual inlet valve fittings together so hoses and quick-connects stay seated
• Prevents accidental hose disengagement that can cause water leaks and interruptions
• Restores the valve's original retaining function when the factory clip is missing or damaged
• Small, low-profile part that works with the valve's inlet fittings to maintain a secure connection

• Two dual inlet valve retaining clips (pack of 2)

• Turn off power and shut off the water supply before servicing the appliance
• Access the inlet valve per your model's service instructions; remove any panels as needed
• Clip simply snaps onto the valve fittings; use needle-nose pliers if needed to seat or remove
• Inspect fittings and hoses for wear or damage and replace any compromised components

This is a replacement clip designed to secure the dual inlet valve fittings on compatible washers and dishwashers, helping keep inlet hoses and valve connections firmly in place and reduce the risk of disconnection. What it does:

• Holds dual inlet valve fittings together so hoses and quick-connects stay seated
• Prevents accidental hose disengagement that can cause water leaks and interruptions
• Restores the valve's original retaining function when the factory clip is missing or damaged
• Small, low-profile part that works with the valve's inlet fittings to maintain a secure connection

• Two dual inlet valve retaining clips (pack of 2)

• Turn off power and shut off the water supply before servicing the appliance
• Access the inlet valve per your model's service instructions; remove any panels as needed
• Clip simply snaps onto the valve fittings; use needle-nose pliers if needed to seat or remove
• Inspect fittings and hoses for wear or damage and replace any compromised components

This dual water inlet valve controls the appliance's hot and cold water flow, restoring proper fill operations and water routing. It's a direct-fit replacement for systems using a two-port inlet valve designed for US plumbing. What it does

• Opens and closes hot/cold water flow to allow normal fill during cycles
• Routes water between inlet lines so the appliance fills at the correct temperature
• Commonly replaces a failed valve when the unit won't fill, fills slowly, or runs continuously
• Helps stop leaks caused by a valve that doesn't fully close

• Disconnect power and shut off water supply before replacing the valve
• Confirm inlet line orientation (hot vs. cold) and secure all hose connections to prevent leaks
• Handle solenoid and electrical connectors carefully; ensure proper connector seating

This thermistor assembly service kit replaces a failing temperature sensor to restore accurate temperature monitoring and control. Ideal for systems that need a direct-replacement sensing element and connector harness. What it does:

• Senses internal temperature and sends a signal to the control board for proper cooling/heating regulation.
• Commonly used when a unit reports incorrect temperature, runs too long, cycles frequently, or shows related error codes.
• Helps prevent overcooling or insufficient cooling caused by a faulty sensor.
• Replaces a damaged or intermittent thermistor connection that can cause inconsistent performance.

• One thermistor assembly service kit (sensor with attached harness/connector as pictured)

• Disconnect power before starting work to avoid shock or equipment damage.
• Handle the sensor and wiring gently; avoid touching the sensing tip with bare hands or contaminating it.
• Route and secure the harness to match the original path; ensure connectors fully seat.

This wiring harness connects the dishwasher's water inlet valves to the control system so valves receive power and signals when a cycle calls for water. Replacing a damaged harness restores reliable valve operation and correct water fill control. What it does:

• Provides power and signal paths between the control board and water inlet valves
• Enables valves to open and close during fill and rinse cycles
• Eliminates intermittent or no-fill symptoms caused by broken wires, burned connectors, or loose plugs
• Maintains factory routing and connector fit for secure electrical connections

• Disconnect power and shut off the water supply before starting work
• Handle connectors gently; match keyed plugs to their mating parts—do not force
• Inspect nearby components (valves, clips, grommets) and replace any damaged items

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This Nozzle Spray Fill Assembly is an OEM part for Fisher & Paykel washing machines. This assembly is integral to the proper distribution of water within the washer during the fill and rinse cycles. 

Issues with the nozzle spray fill assembly can occur due to clogging from mineral deposits, wear and tear, or mechanical damage. A compromised assembly can lead to uneven water distribution, impacting the washer's effectiveness.

Symptoms of a bad nozzle spray fill assembly include:

• Inadequate water flow during the fill cycle.
• Uneven or insufficient wetting of clothes during the wash cycle.
• Prolonged fill times indicate restricted water flow.
• Water spraying unevenly or in an unusual pattern.
• Noticeable leaks or drips from the nozzle area during operation.

This OEM Fisher & Paykel part is also compatible with Bertazzoni, Dacor, and Viking brands.
 

This elbow nozzle directs wash water to the dishwasher spray assembly to help deliver targeted cleaning inside the tub. It restores proper spray direction so dishes and utensils get rinsed more effectively. What it does

• Channels water flow from the pump to the spray arm or distribution tube.
• Restores proper spray pattern when a cracked or clogged nozzle causes weak or misdirected spray.
• Helps prevent pooling and poor cleaning in hard-to-reach areas of the tub.
• Compatible with systems using the SD3-style elbow connection.

• One elbow nozzle

• Disconnect power and water supply to the appliance before starting any repair.
• Remove the lower spray arm or access panel as needed to reach the nozzle; follow your model's service instructions.
• Inspect adjoining hoses, clips, and fittings for wear and replace if damaged.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.