Parts for Frigidaire FCS388CEBA: 06 - Top / Drawer Parts

This warmer drawer assembly replaces a failed or damaged warming drawer to restore the appliance's ability to keep cooked foods warm and ready to serve. Fits as a direct replacement for units using this OEM drawer assembly. What it does:

• Provides the insulated, heated compartment that maintains cooked-food temperature for serving
• Replaces cracked, bent or non-sealing drawers that allow heat loss
• Restores proper drawer movement and latch engagement for safe use
• Helps eliminate intermittent or complete loss of the warming function when the drawer assembly is damaged

• Disconnect power to the appliance before starting any repairs to avoid shock
• Handle the drawer carefully—edges and mounting tabs may be sharp
• Verify proper seating and alignment; ensure connectors and mounting clips engage fully
• If wiring or heating elements are exposed or damaged, replace those components per OEM instructions.

This door gasket seals the refrigerator door to help keep cold air in and warm, humid air out—reducing frost build-up and helping the appliance run more efficiently. Fits where a full perimeter door seal is required. What it does:

• Creates an airtight seal around the refrigerator door to maintain consistent internal temperatures.
• Helps prevent warm air infiltration, moisture, and frost accumulation inside the compartment.
• Reduces energy waste caused by a failing or damaged door seal.
• Common symptoms of a bad seal: condensation at the door, frost on shelves, fluctuating temperatures, or higher energy use.

• Disconnect power to the appliance before attempting any service.
• Remove the old gasket carefully; replacement typically seats into the door channel around the full perimeter.
• Inspect and, if needed, adjust door alignment and hinge condition to ensure a proper seal.

Color: Black. Approx. 29" long.

This safety thermostat helps prevent overheating by cutting power when temperatures get too high. It's a direct-replacement safety control used in heating circuits to protect the appliance and reduce fire risk. What it does:

• Opens the circuit when internal temperatures exceed safe limits to stop heating
• Prevents overheating of components and wiring
• Helps stop recurring high-heat faults that can damage the appliance
• Used as a fail-safe backup to the main temperature control

• One safety thermostat

• Disconnect power to the appliance before servicing to avoid electrical shock
• Replace only with the exact part number to maintain safety function
• Handle terminals carefully; ensure secure electrical connections and proper mounting

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This replacement 10-24 x 3/8 machine screw secures panels, brackets, and small components in compatible Frigidaire appliances. It restores proper fastening where a missing or damaged screw allows parts to shift or rattle. What it does:

• Fastens metal or plastic appliance parts such as trim, brackets, or small assemblies
• Helps eliminate movement, rattling, or loose connections caused by missing or stripped screws
• Restores safe, secure mounting for controls and hardware
• Matches OEM size for proper fit in designated threaded holes

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or nut driver to avoid stripping the head
• Start threads by hand to ensure alignment; tighten until snug — do not over-tighten
• Replace any stripped mating hardware or use correct thread engagement for secure fit

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head