Parts for Frigidaire GCRG3038AFA: Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner

The stainless drawer panel is an OEM replacement part for Frigidaire gas ranges. It is a cosmetic component that serves as the front panel or façade of the drawer compartment located beneath the oven cavity. This panel is typically made of high-quality stainless steel, designed to complement the overall aesthetic of the range and provide a sleek, modern appearance.

Symptoms of a bad or damaged Panel,Drawer,Stainless include:

• Visible dents, scratches, or discoloration on the panel surface
• Difficulty in opening or closing the drawer due to misalignment
• Rust or corrosion on the panel, especially in areas exposed to moisture or spills

Causes of a bad panel can range from accidental impacts or mishandling during installation or use, to prolonged exposure to heat, moisture, or harsh cleaning chemicals. Over time, regular wear and tear can also lead to the deterioration of the panel's appearance or functionality.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas range models.

This replacement control panel restores the user interface that houses the oven/range controls and display, letting you regain a clean, readable console and reliable button access. It's a direct-fit exterior panel designed for factory appearance. What it does:

• Replaces a cracked, scratched, or cosmetic-damaged control surface
• Restores button/keypad access and supports the display/indicator openings
• Helps eliminate issues caused by damaged or warped front panel parts
• Matches factory fit and finish to maintain appliance appearance

• Disconnect power to the appliance before attempting any service
• Handle carefully to avoid scratching the finished surface or damaging clips/tabs
• Use basic hand tools; support the console to prevent stress on wiring and brackets
• Refer to your appliance's service manual or manufacturer instructions for step-by-step removal and reassembly

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement glide helps a refrigerator or freezer drawer open and close smoothly and keeps the drawer aligned for reliable operation. It restores proper sliding action and reduces sticking or scraping. What it does

• Replaces a worn or broken drawer glide to restore smooth drawer movement
• Supports the drawer to prevent sagging and misalignment
• Helps reduce rubbing, sticking, and noisy operation during use
• Maintains proper drawer tracking so the drawer seats correctly

• Disconnect power to the appliance and remove food or contents from the drawer before starting
• Remove the drawer per your model's service instructions to access the glide
• Most installations are simple push-in or screw-replace procedures; keep fasteners from the original assembly

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This part is a genuine main top assembly made for use with ranges.The main top assembly provides a safe and secure surface for the user to balance cookware and heat up food. Over time, the current main top might become worn or damaged, including being dented, bent, corroded, detached, or excessively dirty. In such cases, this part will require replacement. This repair can be done with regular household tools. Make sure the range has been powered off and allowed to cool down entirely before attempting to replace the main top.It is manufactured by Frigidaire and has been sourced directly from the manufacturer. It is sold individually. This main top assembly is manufactured from high-quality, durable, non-corrosive metal. It is an authentic replacement part and thus is compatible with ranges manufactured by Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse.

This cooktop grate replaces a damaged or worn stovetop support to restore stable, even cookware placement and safe burner use. It fits over the burner area and keeps pots and pans level during cooking. What it does:

• Supports cookware securely above the burner for stable cooking
• Helps center heat from the burner for consistent heating
• Replaces cracked, chipped, or warped grates that cause wobbling or poor contact
• Maintains proper clearance between cookware and flame for safe operation

• Allow the range to fully cool and turn off gas/electric before removing or installing the grate
• Lift the old grate straight up; set the replacement into position so it sits flush and stable
• Handle porcelain-coated grates gently to avoid chipping the finish

A heavy-duty cast-iron cooktop grate that supports cookware above gas burners for stable, even heating. Replaces worn or damaged grates to restore pot stability and proper burner clearance. What it does:

• Supports pots and pans over the burner for safe cooking
• Maintains proper clearance for even flame contact and heat distribution
• Restores stability when original grate is cracked, warped, or missing
• Resists high heat and everyday wear for long-lasting use

• One cast-iron cooktop grate

• Allow cooktop to cool completely before removing or installing the grate
• Position the grate securely on the burner supports; no tools required in most models
• Clean with warm soapy water and avoid abrasive cleaners that can damage the finish
• Do not use if the grate is cracked or severely damaged — replace to prevent instability or safety hazards

This cooktop grate replaces a damaged or worn grate on your gas range or cooktop. It supports pots and pans securely over the burner to maintain a stable, level cooking surface and safe, consistent heating.

• Sits above the surface burner to hold cookware at the proper height
• Provides a stable surface to reduce pan wobble, rocking, or tipping
• Replaces grates that are cracked, broken, heavily rusted, or warped
• Helps protect the cooktop from direct flame and cookware contact

• Turn all burners off and allow the cooktop and grate to cool completely before handling
• Lift off the old grate and clean debris from the support pads or recesses
• Set the new grate in place, ensuring all feet sit flat and it's centered over the burner(s)
• Check pan stability before cooking

The Range Cap is an OEM part for Frigidaire ranges. It seals the upper combustion chamber to contain heat from the oven burners. A tight-fitting cap is critical for efficient, safe oven performance.  This cap measures 3 inches in diameter.

Causes of a bad cap can include cracks, warping, or collapsed seals from prolonged exposure to high oven temperatures. Accidental damage during past maintenance is also possible.

Symptoms of a bad cap include:

• Escaping heat from the oven chamber, reducing efficiency
• Flames or sparks visible around the cap during baking
• Loose, wobbly, or missing cap allowing grease and debris in the combustion area

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Range Cap is an OEM part for Frigidaire ranges and cooktops. This cap covers the burner head, protecting it from spills and ensuring an even distribution of heat. It is designed to fit securely over the burner, maintaining both the efficiency and safety of the cooking process.

Causes of a bad range cap include cracking, chipping, or discoloration from repeated use, which can compromise its function and appearance.

Symptoms of a bad range cap include:

• Uneven flame distribution
• Visible cracks or chips
• Discoloration or burnt spots
• Difficulty in fitting the cap securely over the burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Burner Cap is an OEM part for Frigidaire cooktops and ranges. It is designed to cover the burner head, ensuring an even distribution of the flame for efficient cooking. The burner cap also protects the burner head from spills and debris, which can affect performance.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high heat, buildup of food residue, or accidental impacts. A compromised burner cap can lead to uneven flames, inefficient cooking, or difficulty in lighting the burner.

Symptoms of a bad burner cap include:

• Uneven or yellow flames
• Difficulty in igniting the burner
• The burner cap being cracked, chipped, or discolored
• Poor cooking performance or hotspots on cookware

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.