Parts for Whirlpool WRB533CZJB00: Unit Parts

This wire assembly connects the dryer's thermal fuse and thermostat components to the main wiring harness, restoring proper temperature sensing and safety cutoff functions. It helps prevent overheating and allows the dryer to complete heat cycles reliably. What it does:

• Routes electrical connections between the thermal fuse and high-limit thermostat to the dryer control/heat system
• Re-establishes temperature-sensing and safety cutoff circuitry after a damaged or disconnected harness
• Commonly used when a dryer has no heat, intermittent heating, or a blown thermal fuse caused by wiring failure
• Matches OEM wiring layout and connector types for direct replacement

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury
• Inspect connectors and terminals for damage; replace if corroded or melted
• Route wires following the original harness path and secure with existing clips or ties to prevent contact with moving or hot parts

The Compressor is an OEM part specifically designed for Whirlpool French door refrigerators. Located within the refrigerator compartment, it powers the refrigeration system cycle and cooling performance.  

Causes can be a loss of refrigerant or a buildup of condensation inside the sealed compressor casing over many years of use. Motor windings or pistons eventually experience wear from constant cycling.

Symptoms of a bad compressor include:

• The refrigerator is not reaching target temperatures  
• Frost backs up in visible lines or corners
• Distinct electrical burning smells arise  
• Unusual noises occur especially at start-up

This OEM Whirlpool replacement compressor restores efficient, reliable cooling. Its hardened internals withstand condensation and maintain precise motor functioning. 

This part is also compatible with some GE, Crosley, Samsung, and Kenmore French door refrigerators for long-term operation.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

This is the replacement power cord that restores a safe, reliable electrical connection to your appliance. It supplies mains power so the unit can run without intermittent power loss or no-power issues. What it does:

• Provides the main AC connection from the wall outlet to the appliance
• Replaces damaged, frayed, or burned cords that can cause intermittent power or no-power symptoms
• Helps eliminate sparking or overheating at the plug or cord jacket when the existing cord is compromised
• Matches the OEM plug configuration to maintain proper fit and grounding

• One replacement power cord as shown

• Disconnect power at the breaker or unplug appliance before replacing the cord
• Verify cord routing and strain relief to avoid pinching or chafing during reassembly
• Do not use if the replacement cord shows visible damage — return or exchange for a new cord

This grommet is a small protective seal used where a hose, tube, wire, or component passes through or mounts to the appliance cabinet. It cushions the connection and helps prevent leaks, vibration, and wear for reliable operation.

• Provides a snug barrier between parts and metal openings to protect hoses, tubes, and wiring
• Helps seal against moisture to reduce seepage
• Dampens vibration and rattling noises
• Replace if cracked, hardened, missing, or no longer stays seated; symptoms may include drips at a pass-through, buzzing/rattling, or a loose fit

• Disconnect power; shut off water supply if applicable
• Access the grommet location and note orientation/routing
• Remove the old grommet and clean the opening
• Press the new grommet fully into place; reassemble and test for leaks/noise

The Start Device is an OEM part for Whirlpool refrigerators. It aids in the smooth and efficient operation of the refrigerator's compressor. The start device is responsible for providing the necessary electrical boost to start the compressor, which is the main part of the refrigeration coolant system.  

A bad compressor start device can occur due to electrical issues, component failure, or power surges. If you notice symptoms such as the refrigerator not cooling properly, unusual noises coming from the compressor area, or the compressor not starting at all, it may be time to replace this part.

Symptoms of a bad compressor start device include:

• Improper cooling of the refrigerator
• Unusual noises coming from the compressor area
• Compressor not starting

Restore your Whirlpool refrigerator by replacing the faulty or damaged compressor start device with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This capacitor and holder assembly replaces a failed capacitor and its mounting bracket to restore reliable motor start/run support. It helps reduce hard-starting, humming, or intermittent motor operation by returning the original capacitor mounting and function. What it does

• Provides the stored electrical boost needed to help a motor start and run smoothly.
• Secures the capacitor in place to prevent vibration damage and loose connections.
• Commonly addresses symptoms such as hard starts, humming noises, intermittent operation, or motors that fail to start.
• Fits as the direct replacement assembly when the original capacitor and holder have failed.

• Disconnect power to the appliance before beginning any service.
• Capacitors can hold a charge after power is removed; discharge and handle only per manufacturer instructions.
• Basic hand tools are typically required; verify mounting orientation and wiring before removal.

Size: 8-18 x 1/2 inch.