Parts for HWD1600: Washer / Dryer Combo Parts

This manifold blower assembly directs air from the dryer blower housing into the heating and venting path so the appliance dries efficiently. It replaces a cracked or damaged blower manifold to restore proper airflow routing. What it does:

• Channels blower airflow from the blower housing to the heater box and vent
• Prevents air leaks that reduce drying performance or cause inconsistent temperatures
• Helps maintain proper airflow for reliable heating and venting
• Replaces manifolds that are cracked, warped, or broken

• One manifold blower assembly

• Disconnect power before beginning; for gas dryers also shut off the gas supply
• Handle carefully to avoid cracking the plastic mounting tabs; inspect mating surfaces and seals
• After installation, check for proper airflow and secure fit before returning the appliance to service

This hot water valve assembly controls the flow of hot water through the appliance's water system, restoring proper hot-water delivery and preventing unwanted leaks when the valve fails. What it does:

• Regulates hot water flow within the appliance's internal water lines.
• Stops or allows hot water to the dispenser/related subsystem as commanded.
• Commonly replaces a valve that leaks, won't open, or causes no hot water at the dispenser.
• Helps restore proper water control and prevent water damage from a failing valve.

• Disconnect power and shut off the home's water supply before starting.
• Turn off and drain any remaining water lines to avoid spills.
• Replace only with the exact part number for your appliance; secure fittings and test for leaks after installation.

This genuine replacement screw secures appliance panels and components, restoring proper fit and stability after a lost or damaged fastener. It's a direct-fit part used where original screws have worn, stripped, or gone missing. What it does:

• Fastens panels, trim, brackets or small components to maintain appliance alignment and reduce rattling.
• Replaces missing or damaged screws that can cause loose parts or noise.
• Helps restore proper sealing and mechanical function where factory fasteners are required.

• Use the matching screwdriver or bit to avoid stripping the head.
• Hand-start threads before using power tools; do not over-tighten.
• Disconnect power to the appliance and follow OEM safety instructions before servicing.
• Inspect surrounding parts for damage and replace any stripped clips or inserts.

This bake element is the oven's primary heating element that provides consistent heat for baking and roasting. Replaces a failed or damaged element to restore normal oven heating and cooking performance. What it does

• Heats the oven cavity for baking and roasting cycles.
• Restores proper oven temperatures when the original element is burnt out or open.
• Helps eliminate cold spots and inconsistent browning caused by a damaged element.
• May show visible breaks, blistering, discoloration, or cause the oven to not heat at all.

• Disconnect power at the breaker before beginning any repair.
• Handle with care; wear gloves to avoid cuts from sharp edges and allow the element to cool completely.
• Verify fit and terminal type against your appliance before installation; some models require removing the oven floor or back panel.
• If you see arcing or significant damage to wiring or terminals, replace damaged wiring.

This thermostat regulates oven/heater temperature to help maintain consistent cooking or drying performance. It replaces a failed temperature control device so the appliance can heat and cycle correctly. What it does:

• Senses and controls heater temperature to open/close the circuit at set points
• Helps prevent overheating by interrupting power when temperature exceeds the switch setting
• Common symptoms it can address: appliance not reaching or maintaining temperature, heater running continuously, or heater not turning on
• Electrical switching component only—does not include knobs, wiring harnesses, or display assemblies

• One thermostat (heater temperature control switch) as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle terminals carefully; loose connections can cause intermittent operation

This door strike latch secures the refrigerator/freezer door by engaging the striker so the door stays closed and seals properly. It helps restore reliable door closure and can stop doors from popping open unexpectedly. What it does:

• Catches and holds the door closed so the gasket can seal
• Ensures the door engages the striker for consistent closing
• Can stop audible rattling or intermittent opening when the latch is worn
• Helps maintain proper door alignment for better temperature performance

• One door strike latch

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove any door trim or screws that block access to the latch assembly
• Replace the latch, align it with the striker, then tighten fasteners securely
• Test the door operation several times to ensure proper engagement and sealing