Parts for Frigidaire RS229GCF2: 05 - Cabinet Parts

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This part has been discontinued by the manufacturer and is no longer available.

This door-actuated light switch replaces a worn or failed refrigerator light control so the interior light turns on and off when the door opens. Restores reliable lighting and helps you see food clearly. What it does:

• Closes and opens the light circuit when the refrigerator/freezer door is opened or closed
• Commonly used when the interior light stays on, won't turn on, or flickers intermittently
• Controls the lamp only; does not include bulbs or housing components
• Matches OEM fit and mounting for a direct replacement

• One door-actuated light switch

• Disconnect power or unplug the appliance before replacing the switch
• Remove the light bulb and bezel or access panel as required to reach the switch
• Replace the switch with the same orientation and secure mounting; reconnect wiring to factory terminals
• Test operation by restoring power and opening the door

Note: This is a 1/4" x 1/4" compression elbow fitting without the nuts. See part# 4932JA3009A which is a 1/4" by 1/4" John Guess quick connector elbow. 

Specs: 7/16 x 20

A small replacement pin used to secure and align moving parts in the appliance for reliable operation and correct fit. Replaces a worn or broken locating/hinge pin to reduce play and restore proper movement. What it does:

• Secures and locates a pivot or hinge point so doors, panels, or components stay aligned
• Maintains correct spacing to prevent rubbing, binding, or uneven closing
• Restores stable movement when the original pin is worn, bent, or damaged
• Helps reduce rattling or excessive play at the pivot/hinge area

• Disconnect power and empty/remove any attached panels or doors before starting
• Use basic hand tools; support the component while removing/installing the pin to avoid damage
• Inspect mating parts (bushings, brackets) and replace if excessively worn
• Take care to control spring release to avoid injury

This part has been discontinued by the manufacturer and is no longer available.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This tube clamp secures small tubing and lines inside the appliance to prevent movement and reduce wear. It keeps hoses and tubes routed properly so they don't rub against sharp edges or vibrate during operation. What it does:

• Holds water, drain or refrigerant tubing in place to prevent sagging and chafing
• Reduces vibration and rattling from loose lines
• Helps prevent tubing wear that can lead to leaks or pinch damage
• Keeps hoses routed neatly for reliable appliance operation

• Disconnect power and shut off water supply before beginning any repair
• Remove any access panels needed to reach the clamp location; use caution around sharp sheet metal
• Replace only the damaged clamp with the same style and secure tubing firmly but without over-tightening
• If tubing shows damage where it was rubbing, replace or repair the tubing before reinstalling the clamp