Parts for Amana BL20QL / P1125508W L: 01 - Page 1 Parts

A single replacement screw used to fasten appliance panels and components, restoring secure fit and reducing vibration or noise. Simple, low-cost part for repairs that need a missing or stripped fastener. What it does:

• Secures panels, trim, or small component housings to the appliance frame
• Helps stop rattling, vibration, and misalignment caused by loose or missing screws
• Keeps internal components properly seated to maintain normal operation
• Used wherever the OEM specifies this exact fastener

• One replacement screw

• Disconnect power before servicing the appliance to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand first, then tighten snugly—do not overtighten
• Keep small parts away from children and pets

A replacement white freezer door gasket that seals the freezer compartment to help maintain proper temperature and efficiency. Restores a tight seal to reduce cold-air loss and help keep food frozen. What it does:

• Seals the freezer door to prevent cold-air leaks and reduce frost buildup.
• Helps the freezer maintain consistent internal temperature for proper cooling.
• Can reduce excessive run time caused by a worn or damaged seal.
• Addresses common symptoms like visible gaps, soft or torn seal, and increased frost.

• One white freezer door gasket

• Unplug the appliance before beginning any repair to avoid electrical hazard.
• Remove the old gasket carefully; warm the new gasket slightly if needed to ease installation and ensure a snug fit.
• Inspect the door flange for damage or debris before installing the new gasket.
• After installation, close the door and allow up to 24 hours for the gasket to fully seat; check for any remaining gaps and adjust if necessary.

Color: White - For almond use C8944913Q. For black use C8944912Q

Almond. For white use C8944909Q. For black use C8944912Q

Includes both shims as seen in the photo

This part has been discontinued and is no longer available.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This part has been discontinued by the manufacturer and is no longer available.