Parts for Maytag AEP222VAW0: 02 - Oven Door And Drawer Parts

Right hand side

Left hand side

This sheet-metal pan-head screw secures appliance panels, brackets, and components to the cabinet or frame. Replacing a missing or damaged screw restores a tight fit and helps stop rattles, misalignment, and loosening.

• Fastens sheet-metal panels, covers, ducts, and brackets to the appliance chassis
• Helps keep components aligned and secure during operation
• Replace if the original is missing, rusted, stripped, or damaged
• Common symptoms: loose or vibrating panels, gaps or misaligned parts, hardware that won't tighten

• Disconnect power; shut off gas or water supply before servicing
• Support the panel or part being attached; hand-start threads to avoid cross-threading
• Use the correct driver bit; tighten snugly but do not overtighten into sheet metal
• If multiple matching screws secure a part, consider replacing them as a set for consistent hold

Replacement screw used to secure components and panels in household appliances, restoring proper fit and effectively reducing movement or rattling from loose or missing fasteners. What it does:

• Secures panels, trim and internal components to keep parts aligned and stable.
• Helps stop rattling, vibration or noise caused by loose or missing fasteners.
• Restores proper mounting for brackets, covers and control housings.
• Useful wherever a worn or stripped screw is causing play or loose parts.

• Disconnect power and unplug the appliance before doing any work.
• Use the correct driver and size to avoid stripping the head or threads.
• Tighten snugly but avoid overtightening—replace with the exact OEM screw when specified.

This factory fastener secures appliance panels, brackets, and internal components so everything stays aligned and quiet. Replacing a missing or damaged screw restores a tight fit and helps reduce vibration, rattles, and wear.

• Fastens metal or plastic parts to the cabinet/frame
• Maintains alignment of covers, ducts, housings, and brackets
• Replace if the head is stripped, threads are worn, or hardware is missing
• Symptoms can include loose or misaligned panels, rattling/vibration noises, or parts that won't stay secured

• Disconnect power and shut off gas/water before service.
• Match the screw to the original location and reuse existing holes/mounts.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Use the correct driver bit to prevent stripping the head.

This screw secures appliance components such as panels, brackets, and internal assemblies to the cabinet or frame. Replacing worn or missing hardware restores a tight fit, reduces vibration, and helps prevent damage from loose parts.

• Fastens and stabilizes parts to maintain proper alignment
• Helps eliminate rattling or vibration from loose panels/brackets
• Replaces missing or stripped hardware during repairs
• Supports proper reassembly after service

• Disconnect power before service; turn off water supply
• Match the original screw's location; replace like-for-like length and thread
• Start threads by hand to avoid cross-threading; use the correct driver/bit
• Tighten snugly; do not overtighten, especially into plastic

Color: White. Size: 8-18 x 3/8 inch.

This push-on nut is a press-fit retainer that secures components to a smooth shaft or stud. Use it to restore a tight, reliable hold when the original fastener is missing, bent, or no longer grips securely.

• Provides a friction hold on a shaft or stud to keep parts from sliding off
• Helps reduce wobble, vibration, or rattling caused by a loose or missing retainer
• Common signs of failure: component won't stay in place, falls off, or feels loose
• Direct replacement for a deformed or lost push nut

• Disconnect power and shut off gas/water before servicing
• Remove the old retainer carefully; do not reuse a distorted push nut
• Align and press the new push nut straight onto the shaft/stud; a deep socket can help apply even pressure
• Verify full engagement; do not hammer near glass, porcelain, or delicate surfaces

Factory replacement screw that secures appliance components and hardware. Use it to replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and help prevent loosening or damage from vibration.

• Fastens brackets, panels, or internal parts at the original mounting points
• Replaces worn or missing hardware to correct loose or misaligned components
• Helps reduce vibration-related noise and movement
• Matches the original thread and length specified for the application

• Disconnect power; shut off water or gas if applicable before servicing
• Compare to the original for thread and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any original spacers/washers if present; replace if damaged

This flat washer is a small hardware spacer that helps distribute load and protect mating surfaces on appliance assemblies. It restores secure, even clamping at fastener joints to reduce wear and vibration. What it does:

• Provides a smooth bearing surface to distribute pressure from a bolt or screw
• Helps prevent fastener pull-through and reduces localized metal deformation
• Minimizes loosening from vibration by improving clamp load distribution
• Protects mating parts from direct metal-on-metal contact and wear

• Disconnect power and follow appliance safety procedures before working on the unit
• Use the correct fastener and seating position; replace any damaged or corroded hardware
• Inspect mating surfaces and clean debris before installation for a secure fit
• If reusing fasteners, ensure proper torque per manufacturer specs

This 20-inch towel bar is a direct-replacement handle that restores a secure, comfortable grip for opening and closing your appliance door. Ideal when the original bar is cracked, loose, or missing to improve function and appearance. What it does:

• Provides a sturdy handle for opening and closing the appliance door
• Replaces cracked, loose, bent, or broken towel bars
• Restores the appliance's finished look and user comfort
• Mounts to the door where the original towel bar was attached

• Disconnect power and unplug the appliance before starting any repair
• Use common hand tools; retain all original fasteners and trim pieces unless replacement hardware is specified
• Access may require removing the door or an inner door panel—refer to the appliance's service diagram
• Test the door operation after installation to ensure secure fit and alignment

Replacement door hinge that supports and secures the appliance door, restoring proper alignment for smooth opening and closing. Ideal when the door sags or rubs against the cabinet. What it does

• Provides the pivot point that holds and aligns the door for even gaps and a proper seal.
• Restores smooth, stable opening and closing when a worn hinge causes sticking or noisy movement.
• Helps correct door sagging, rubbing or scraping, and prevents uneven wear on the gasket.
• Replaces bent, corroded or damaged hinge hardware that interferes with proper door operation.

• Disconnect power to the appliance (unplug or switch off at the breaker) before beginning work.
• Support the door securely (use a helper or a support block) before removing hinge fasteners to prevent injury or damage.
• Use basic hand tools; avoid overtightening fasteners—tighten until snug and check door alignment then adjust as needed.

This replacement bumper cushions and protects appliance panels and doors to reduce vibration, prevent chipping, and stop rubbing or rattling. It restores a quiet, secure fit where the original bumper has worn or fallen off. What it does:

• Acts as a soft stopper to prevent doors, drawers, or panels from banging or contacting metal surfaces
• Reduces vibration and rattling during operation
• Protects finishes from chips, scratches, and wear at contact points
• Helps restore proper alignment and snug fit where the original bumper is missing or compressed

• One replacement bumper (1 count)

• Clean and dry the mounting surface; remove any old adhesive or debris before installing
• Press the bumper firmly into place; some bumpers use adhesive backing or fit into a recess—verify fit before final placement
• If adhesive is used, allow time for proper bonding per adhesive instructions; avoid using the appliance until secure
• For safety, disconnect power to the appliance before accessing panels or doors

Right hand side. For left hand use 98004952

Left hand side. For right hand use 98004953