Parts for Thermador GPS364GD: 02 - Trim & Control Panel Parts

This part has been discontinued by the manufacturer and is no longer available.

This side-trim gasket seals the edge of the appliance door/trim to help maintain a clean fit and reduce rattling or light air leakage. It restores the door edge seal for a neater appearance and improved closing performance. What it does:

• Seals the door side trim to help reduce noise and prevent light air or moisture intrusion
• Helps maintain proper alignment and fit of the door trim for smooth opening and closing
• Replaces worn, torn or compressed trim gasket that can cause rubbing or gaps
• Supports overall door aesthetics by restoring a continuous seal line

• One side-trim gasket

• Basic trim removal may be required
• Inspect mating surfaces and remove old adhesive or debris before installing the new gasket
• Use gentle pressure to seat the gasket; avoid stretching or over-tensioning
• Disconnect power to the appliance before doing any service that exposes electrical components

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

This is a replacement grease tray cover that restores the oven/cooktop drip area to help contain grease and protect the tray below. It improves grease containment and keeps the cooking area looking finished. What it does:

• Covers the grease collection area to help contain drips and splatters
• Helps prevent grease from pooling on the tray and reduces cleanup
• Restores a damaged or missing cover so the appliance looks and functions correctly
• Can reduce smoke and odors caused by exposed grease buildup

• One grease tray cover

• Ensure the appliance is completely cool and power/gas is turned off before starting
• Remove the old cover and clean the tray area; use gloves to handle greasy parts
• Align the new cover with the tray opening and seat it in place per the appliance instructions

This part is no longer available.

This is a 1/4-20 hex keps nut — a hex nut with an attached captive washer that helps secure panels, brackets, and fasteners. It provides a simple, vibration-resistant fastening solution for appliance assemblies. What it does

• Fastens components to machine frames, panels, and brackets using a 1/4-20 bolt or stud.
• Captive washer helps resist loosening from vibration and movement.
• Commonly used where a compact, pre-assembled nut-and-washer is needed for reliable retention.
• Replace when threads are stripped, washer is damaged, or parts wobble or rattle.

• One hex keps nut (1/4-20).

• Disconnect power and follow appliance safety procedures before working on hardware.
• Use the correct 1/4" socket or wrench to install; hold the mating bolt head as needed to tighten.
• Tighten securely but avoid over-tightening to prevent thread damage or distortion.
• Replace with the same nut type and size to maintain fit and vibration resistance.

Package of 60 pyramid shaped briquettes

This 1/2-inch foam adhesive tape cushions and seals appliance gaps to reduce vibration and prevent rubbing or rattling of panels. It's a simple, flexible trim that restores fit and quiets noisy or loose parts. What it does:

• Provides a soft, compressible barrier to reduce panel-to-panel contact and eliminate rattles
• Helps seal small gaps to keep out dust and reduce drafts around doors or trim
• Cushions components to damp vibration and protect finishes from wear
• Conforms to irregular surfaces for easy placement in tight spots

• Access the area with the appliance powered off and, if applicable, unplugged for safety
• Clean and dry the surface before applying for best adhesion
• Cut to fit with scissors or a utility knife and press firmly to set the adhesive
• Replace if the foam is compressed, torn, or no longer adheres