Parts for Amana DRB2101BC / PDRB2101BC0: 04 - Door Handles & Accessories Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This freezer door handle restores a secure, comfortable grip on your refrigerator's freezer door. Replace it when the original is cracked, loose, or missing to maintain safe operation, clean appearance, and easy everyday access.

• Provides the handhold used to open and close the freezer door
• Attaches to the door's existing mounting points/fasteners for a secure fit
• Helps resolve issues such as a broken, cracked, or wobbly handle
• Can improve ease of opening if the old handle has failed

• Disconnect power before servicing; wear cut-resistant gloves
• Support the old handle, then loosen/remove its fasteners; note their placement
• Position the new handle on the existing mounts and tighten fasteners evenly
• Do not overtighten; verify alignment and that the handle is secure

This screw kit provides replacement fasteners used to secure appliance panels and internal components, helping restore proper fit and reduce vibration or rattling caused by missing or damaged screws. Ideal for maintenance and small repairs. What it does:

• Replaces missing, stripped, or damaged screws to restore secure panel and component attachment
• Helps eliminate rattling, vibration, and loose or misaligned panels
• Allows reassembly after part replacement or routine service
• Works with the appliance's original mounting points and threaded holes

• Always disconnect power and, if applicable, gas supply before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping screw heads
• Tighten screws snugly but avoid over-torquing which can strip threads or crack panels
• Keep small fasteners away from children and pets; work on a stable, well-lit surface

A small replacement clip-style retainer that secures the appliance toe grille to the cabinet, keeping the grille flush and in place. Replaces worn or broken clips to restore proper fit and appearance. What it does:

• Secures the toe/grille panel to the appliance cabinet so the grille stays aligned and snug
• Stops the grille from sagging, rattling, or popping off during use
• Fits into designated mounting slots or tabs to lock the grille in place
• Commonly replaced when clips are cracked, missing, or loose

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the toe grille by removing any screws or releasing retaining tabs per your model's service instructions
• Press the clip into the grille/cabinet mounting slot until it snaps in place; verify the grille seats evenly
• If multiple clips are damaged, replace all needed clips for a secure fit

This part has been discontinued and is no longer available.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles