Parts for Thermador VTN1000Q: 04 - Model Vtr1000q Parts

This part has been discontinued by the manufacturer and is no longer available.

This part is a replacement blower motor. This part can be used to replace broken or defective blower motor in a variety of downdraft vent models. This part rotates the blower wheel, allowing the appliance to draw smoke and odors into the vent. If motor is broken, the vent likely will not work efficiently, if at all. Thus, this part should be immediately replaced. Before any repairs are made, the appliance should be entirely disconnected from the power sources and work gloves should be worn.This is a genuine OEM part made by Bosch and has been sourced directly from the manufacturer. As an authentic replacement part, this blower motor is suitable for use on downdraft vents manufactured by Bosch and some other brands.

A protective terminal boot that slips over a capacitor connection to shield it from moisture, dirt and accidental contact, helping reduce risk of shorts and maintain a reliable electrical connection. What it does:

• Covers the capacitor terminal to reduce the chance of accidental contact and arcing.
• Protects the terminal from moisture, dust and debris that can compromise electrical connections.
• Helps prevent corrosion and keeps the terminal area cleaner for more reliable operation.
• Signs it may be needed: cracked, torn or missing boot; visible arcing or burn marks near the capacitor; intermittent electrical behavior that points to a compromised connection.

• Always disconnect power and unplug the appliance before working on electrical components.
• Discharge the capacitor per OEM instructions before touching terminals to avoid shock.
• Push the boot fully onto the terminal for a snug fit; ensure no wiring is pinched or under strain.

The Exhaust Fan Capacitor is an OEM part for Bosch range hoods. This part provides the necessary electrical charge to start and run the fan motor efficiently. It ensures that the range hood can effectively ventilate smoke, odors, and grease from your kitchen.

Causes of a bad capacitor can include electrical surges, wear and tear over time, or overheating. 

Symptoms of a bad exhaust fan capacitor include:

• The exhaust fan not starting or running intermittently
• Unusual noises coming from the fan motor
• Reduced airflow or ventilation performance
• The range hood not operating at its full capacity

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

A welded baseplate assembly that provides the structural mounting support for the appliance's lower chassis and components, restoring proper alignment and stability for safe operation. What it does:

• Anchors and supports motor, pump, and lower-frame components to maintain correct positioning
• Replaces a cracked, bent, or corroded baseplate that can cause vibration, noise, or misalignment
• Restores mounting points needed for secure fastener engagement and component alignment
• Helps reduce abnormal movement or rubbing that can lead to additional wear

• One welded baseplate assembly

• Intended for professional or experienced DIY installation;
• Power off and unplug the appliance, and remove water supply if applicable, before disassembly
• Retain and reuse original fasteners when possible; replace any damaged hardware

This genuine OEM part is a blower wheel for range hoods. The blower wheel is the main fan that is used to circulate air above the stove. If the blower is no longer turning on, not working as efficiently, or barely operating, it will need to be replaced.To begin, make sure that the range and range hood are unplugged. Once they have been powered off, proceed to remove the bottom panel of the range hood by unfastening the mounting screws that secure it. Once removed, locate the old blower wheel. Remove the mounting screws that attach it to the range vent and pull it out of its place. Proceed to install the new blower wheel by fastening the screws that attach it to the vent. Once secured, reinstall the bottom panel of the range hood.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ranges and range hoods.

This part has been discontinued by the manufacturer and is no longer available.

A locknut that secures threaded shafts and fasteners in appliances to resist loosening from vibration and maintain stable component alignment. Replacing a damaged or stripped locknut restores a secure fastening and reduces rattling or movement. What it does:

• Keeps nuts and components locked on threaded shafts to prevent backing off under vibration.
• Commonly used where a retained fastener is required on motors, pumps, or moving assemblies.
• Replace if you notice loose parts, persistent rattling, or visible thread damage.
• Restores proper fastening to help prevent premature wear or component misalignment.

• Disconnect power (and water/gas if applicable) before servicing the appliance.
• Use the correct size socket or wrench and hold the mating component to avoid over-torquing.
• Inspect mating threads and replace any damaged hardware to ensure a secure fit.